Indian · Indian side-valve, total-loss (Powerplus, early Scout and Chief 1916-1932)

Scout (101 and earlier)

Library entry covers 1920-1931

2 factory 60 guideline

Published source

Correct Lubrication of Indian Motocycles: Chief, Scout and Standard Models (Indian factory booklet, mid-1920s; pages missing)

Factory owner's handbook. Covers 1920-1925 era booklet.

Open the source

62 items for a 1920 model, grouped by interval the way a factory chart is laid out.

How this bike is built (what the schedule is based on)

Engine cycle: Four-stroke
Engine lubrication: Total-loss (hand pump / drip feed / mechanical pump to waste)
Oil filtration: None (no filter)
Valve gear: Side valve (flathead)
Ignition: Magneto (incl. magdyno, flywheel magneto)
Charging: None (magneto only / no battery charging)
Battery: Wet cell (flooded lead-acid, needs topping up)
Fuel system: Single carburetor
Cooling: Air / oil cooled
Primary drive: Gear or chain inside engine, shares engine oil
Gearbox oil: Separate gearbox oil
Clutch control: Foot clutch / hand shift
Final drive: Chain
Front suspension: Leaf-spring fork (Indian, early BMW)
Rear suspension: Rigid (hardtail)
Front brake: Drum (or band / stirrup)
Rear brake: Drum (or band / belt rim)
Wheels: Spoked, tubed
Sidecar: No sidecar

Maintenance schedule

1920 Indian Scout (101 and earlier)

On the road: every 50 mi

1 item

Top up total-loss oil tank, check drip feed / pump rate

Pre-ride / on the road

Guideline

Total-loss engines burn their oil by design. Check the sight glass or drip rate and give hand-pump charges as the manual and conditions require.

On the road: every 300 mi

3 items

Acetylene / oil lamps: check carbide, water and wicks

Pre-ride / on the road

Guideline
Check tire pressures

Pre-ride / on the road

Guideline
Lubricate drive chain

Pre-ride / on the road

Guideline

Lube warm, ideally at the end of the riding day so it soaks in overnight. Sooner after rain.

On the road: every 500 mi

2 items

Grease girder / springer fork links

Pre-ride / on the road

Guideline

Grease gun on every nipple until clean grease shows. Touring days add up fast.
Walk-around: check nuts and bolts for vibration loosening

Pre-ride / on the road

Guideline

Old machines shake things loose: exhaust nuts, mudguard stays, footrests, tank mounts, battery strap.

On the road: every 600 mi

1 item

Check chain slack and rear wheel alignment

Pre-ride / on the road

Guideline

On the road: every 1,000 mi

1 item

Check road kit: plugs, points file, master link, tube patches, wire, tape

Pre-ride / on the road

Guideline

Every 500 mi

2 items

Drain residual oil from crankcase (total-loss)

Engine

Factory

Manual: Draining and cleaning the crankcase (drain, flush with oil, refill to level). Factory: Booklet pages nine-ten: every 500 miles; no kerosene flushing
Check gearbox oil level

Primary and gearbox

Factory

Manual: Check transmission and primary drive case oil level. Factory: Booklet page fourteen: every 500 miles, top up to level hole

Every 1,000 mi or 6 months

8 items

Inspect, clean and gap spark plugs

Engine

Guideline
Lubricate manual advance / retard control and cable

Ignition and electrics

Guideline
Adjust foot clutch and hand-shift linkage, lubricate pivots

Primary and gearbox

Guideline
Adjust front drum brake

Brakes

Guideline
Adjust rear drum brake and rod / cable linkage

Brakes

Guideline
Check spoke tension and wheel true

Wheels and tires

Guideline
Inspect tire tread, sidewalls and date codes

Wheels and tires

Guideline
Lubricate control cables and lever pivots

Controls and cables

Guideline

Every 1,000 mi or 12 months

1 item

Grease saddle pivot, check saddle springs / seat post

Rear suspension and frame

Guideline

Every 1,500 mi or 6 months

2 items

Clean / inspect air filter

Fuel and air

Guideline

Mesh or oiled foam: clean and re-oil. Paper: blow out or replace. Some very early machines have no filter at all.
Clean drive chain thoroughly (remove and soak, re-lube)

Final drive

Guideline

Non O-ring chains on old machines: remove, clean, soak in hot chain grease or lube, refit with the master link clip closed end leading.

Every 1,500 mi or 12 months

1 item

Check and adjust valve clearances

Engine

Guideline

Every 2,000 mi or 12 months

3 items

Inspect hand pump, check valves and drip-feed sight glass

Engine

Guideline
Change gearbox oil

Primary and gearbox

Guideline
Inspect leaf spring fork: leaves, shackles, bushes

Front end

Guideline

Every 3,000 mi or 12 months

13 items

Check engine mounting bolts and plates

Engine

Guideline
Check throttle cable(s) free play and return

Fuel and air

Guideline
Clean fuel tap filter / sediment bowl

Fuel and air

Guideline
Check / set ignition timing

Ignition and electrics

Guideline
Clean and gap contact breaker points, oil cam felt

Ignition and electrics

Guideline
Adjust clutch pushrod / clutch adjuster

Primary and gearbox

Guideline
Check chain guard, chain oiler (if fitted), rear chain case

Final drive

Guideline
Inspect chain and sprockets for wear (measure stretch)

Final drive

Guideline
Check steering damper (friction or hydraulic)

Front end

Guideline
Check steering head bearing adjustment

Front end

Guideline
Check footrests, pegs, rear brake and gear lever pivots

Rear suspension and frame

Guideline
Grease and check center / side stand and springs

Rear suspension and frame

Guideline
Check wheel bearings for play

Wheels and tires

Guideline

Every 4,000 mi or 12 months

2 items

Replace spark plugs

Engine

Guideline
Lubricate brake cam spindles, check linings and drums

Brakes

Guideline

Every 4,000 mi or 2 years

1 item

Decarbonize head, grind / lap valves (top-end decoke)

Engine

Guideline

Period practice. Leaded-era valve seats may need hardened seats for unleaded fuel.

Every 5,000 mi or 2 years

1 item

Check cylinder head bolt torque

Engine

Guideline

Air-cooled iron and alloy engines can lose head bolt tension; follow your manual's sequence and whether it is done hot or cold.

Every 6,000 mi or 12 months

2 items

Clean carburetor float bowl(s), check float level and jets

Fuel and air

Guideline

Ethanol fuel varnishes old carbs quickly in storage.
Lubricate speedometer / tachometer cables, check drive

Controls and cables

Guideline

A dry speedo cable whips the needle and eventually kills the instrument.

Every 6,000 mi or 2 years

4 items

Check engine breather and oil return

Engine

Guideline
Lubricate and check automatic advance unit

Ignition and electrics

Guideline
Magneto: clean slip ring and pickup brush, check HT lead

Ignition and electrics

Guideline
Repack / replace wheel bearings

Wheels and tires

Guideline

Cup-and-cone and taper roller hubs need periodic repacking and adjustment.

Every 10,000 mi or 2 years

1 item

Compression test (or leak-down)

Engine

Guideline

Every 10,000 mi or 3 years

1 item

Repack / replace steering head bearings

Front end

Guideline

Many old machines use loose balls in cups and cones. Taper roller conversions are common.

Every 10,000 mi

1 item

Replace chain and sprockets (wear based)

Final drive

Guideline

Every 12,000 mi or 3 years

1 item

Replace points and condenser

Ignition and electrics

Guideline

Every 15,000 mi or 5 years

1 item

Inspect clutch plates and springs

Primary and gearbox

Guideline

Every 15,000 mi

1 item

Replace brake linings / skim drums (wear based)

Brakes

Guideline

Every 25,000 mi or 10 years

1 item

Magneto overhaul / re-magnetize, replace capacitor

Ignition and electrics

Guideline

Weak spark when hot is the classic symptom. Old capacitors fail with age, not miles.

Every 12 months

1 item

Check speedometer / odometer against a known distance

Controls and cables

Guideline

Old speedos drift with tire size and drive wear. Use phone GPS over a measured 10 miles / km.

Every 2 years

3 items

Inspect fuel tank for rust, sealer failure, leaks

Fuel and air

Guideline
Inspect wiring, bullet connectors and ground points

Ignition and electrics

Guideline
Inspect frame, welds and lugs for cracks

Rear suspension and frame

Guideline

Every 4 years

1 item

Replace fuel lines

Fuel and air

Guideline

Old rubber and modern ethanol fuel do not mix well.

Every 6 years

2 items

Replace inner tubes and rim tape with tires

Wheels and tires

Guideline
Replace tires on age (regardless of tread)

Wheels and tires

Guideline

Guideline lines: Intervals here are general guidelines for the machine's era and layout, compiled for this app. They are not factory manual figures. Check your workshop manual, and edit any interval in the bike's Schedule tab.