Suzuki · Suzuki two-stroke twin / triple (T20-T500, GT 1965-1977)

GT750 'Water Buffalo'

Library entry covers 1972-1977

26 factory 47 guideline

Published source

Suzuki GT750M Owner's Manual (Suzuki Motor Co.), Lubrication Chart and Periodic Inspection Chart pp.38-40

Factory owner's handbook. Covers 1975 GT750M owner's manual (liquid-cooled triple, front disc); intervals in miles and km.

Open the source

73 items for a 1972 model, grouped by interval the way a factory chart is laid out.

How this bike is built (what the schedule is based on)

Engine cycle: Two-stroke
Engine lubrication: Two-stroke oil injection (Autolube, Injectolube, Pilgrim pump...)
Oil filtration: None (no filter)
Valve gear: None (two-stroke porting)
Ignition: Battery and coil with contact points
Charging: Alternator / stator with rectifier
Battery: Wet cell (flooded lead-acid, needs topping up)
Fuel system: Two or more carburetors
Cooling: Liquid cooled
Primary drive: Gear or chain inside engine, shares engine oil
Gearbox oil: Separate gearbox oil
Clutch control: Hand lever, cable
Final drive: Chain
Front suspension: Telescopic fork
Rear suspension: Swingarm, twin shocks
Front brake: Disc, hydraulic
Rear brake: Drum (or band / belt rim)
Wheels: Spoked, tubed
Sidecar: No sidecar

Maintenance schedule

1972 Suzuki GT750 'Water Buffalo'

On the road: every 150 mi

1 item

Check two-stroke oil tank / carry premix oil

Pre-ride / on the road

Guideline

Running a two-stroke out of oil seizes it. Injection bikes: check the tank. Premix: carry oil and a measure.

On the road: every 300 mi

3 items

Check lights, horn, brake light switches

Pre-ride / on the road

Guideline
Check tire pressures

Pre-ride / on the road

Guideline
Lubricate drive chain

Pre-ride / on the road

Guideline

Lube warm, ideally at the end of the riding day so it soaks in overnight. Sooner after rain.

On the road: every 500 mi

1 item

Check coolant level

Pre-ride / on the road

Guideline

On the road: every 600 mi

1 item

Check chain slack and rear wheel alignment

Pre-ride / on the road

Guideline

On the road: every 1,000 mi

1 item

Check road kit: plugs, points file, master link, tube patches, wire, tape

Pre-ride / on the road

Guideline

On the road: every 4,000 mi

1 item

Walk-around: check nuts and bolts for vibration loosening

Pre-ride / on the road

Factory

Manual: Bolts, nuts and spokes: retighten. Factory: Lubrication chart p.38, periodic inspection chart pp.39-40: first at 750 mi

Every 500 mi

1 item

Clean drive chain thoroughly (remove and soak, re-lube)

Final drive

Factory

Manual: Drive chain: lubricate with chain lube or motor oil. Factory: Lubrication chart p.38, periodic inspection chart pp.39-40: adjusted every 2,000 mi, washed every 4,000 mi

Every 1,000 mi or 6 months

1 item

Check gearbox oil level

Primary and gearbox

Guideline

Every 2,000 mi or 12 months

1 item

Grease swingarm pivot

Rear suspension and frame

Guideline

Every 2,000 mi

11 items

Check / bleed / adjust oil injection pump cable

Engine

Factory

Manual: Oil pump: check operation, adjust control lever aligning marks. Factory: Lubrication chart p.38, periodic inspection chart pp.39-40: first at 750 mi
Check cylinder head bolt torque

Engine

Factory

Manual: Cylinder head nuts and exhaust fitting nuts: retighten. Factory: Lubrication chart p.38, periodic inspection chart pp.39-40: first at 750 mi
Inspect, clean and gap spark plugs

Engine

Factory

Manual: Spark plugs: clean and adjust gap. Factory: Lubrication chart p.38, periodic inspection chart pp.39-40: first at 750 mi
Clean / inspect air filter

Fuel and air

Factory

Manual: Air cleaner element: wash. Factory: Lubrication chart p.38, periodic inspection chart pp.39-40
Synchronize carburetors

Fuel and air

Factory

Manual: Carburetors: adjust idle adjust screw and pilot screw. Factory: Lubrication chart p.38, periodic inspection chart pp.39-40: first at 750 mi
Check battery electrolyte, top up with distilled water

Ignition and electrics

Factory

Manual: Battery: check and service electrolyte. Factory: Lubrication chart p.38, periodic inspection chart pp.39-40: first at 750 mi
Clean and gap contact breaker points, oil cam felt

Ignition and electrics

Factory

Manual: Contact points: check gap and ignition timing; grease cam oil felt. Factory: Lubrication chart p.38, periodic inspection chart pp.39-40: first at 750 mi; felt greased every 3,000 mi
Adjust clutch free play, lubricate cable and lever pivot

Primary and gearbox

Factory

Manual: Clutch: adjust. Factory: Lubrication chart p.38, periodic inspection chart pp.39-40: first at 750 mi
Adjust rear drum brake and rod / cable linkage

Brakes

Factory

Manual: Rear brake: adjust play. Factory: Lubrication chart p.38, periodic inspection chart pp.39-40: first at 750 mi
Check brake pads and discs

Brakes

Factory

Manual: Front brake: check fluid level, leakage and pads. Factory: Lubrication chart p.38, periodic inspection chart pp.39-40: first at 750 mi
Inspect tire tread, sidewalls and date codes

Wheels and tires

Factory

Manual: Tires: check tread condition. Factory: Lubrication chart p.38, periodic inspection chart pp.39-40

Every 3,000 mi or 12 months

12 items

Check engine mounting bolts and plates

Engine

Guideline
Check / set ignition timing

Ignition and electrics

Guideline
Adjust clutch pushrod / clutch adjuster

Primary and gearbox

Guideline
Check chain guard, chain oiler (if fitted), rear chain case

Final drive

Guideline
Inspect chain and sprockets for wear (measure stretch)

Final drive

Guideline
Check steering damper (friction or hydraulic)

Front end

Guideline
Check steering head bearing adjustment

Front end

Guideline
Inspect fork seals, stanchions and fork boots

Front end

Guideline
Check footrests, pegs, rear brake and gear lever pivots

Rear suspension and frame

Guideline
Grease and check center / side stand and springs

Rear suspension and frame

Guideline
Check spoke tension and wheel true

Wheels and tires

Guideline
Check wheel bearings for play

Wheels and tires

Guideline

Every 3,000 mi

3 items

Change gearbox oil

Primary and gearbox

Factory

Manual: Transmission oil: change. Factory: Lubrication chart p.38, periodic inspection chart pp.39-40: first at 750 mi; chart lists 3,000 mi / 3,000 km
Lubricate brake cam spindles, check linings and drums

Brakes

Factory

Manual: Rear brake cam shaft: grease. Factory: Lubrication chart p.38, periodic inspection chart pp.39-40
Lubricate control cables and lever pivots

Controls and cables

Factory

Manual: Clutch, throttle and brake cables: oil. Factory: Lubrication chart p.38, periodic inspection chart pp.39-40

Every 4,000 mi or 12 months

1 item

Replace spark plugs

Engine

Guideline

Every 4,000 mi

4 items

Decarbonize exhaust ports, pipes and baffles

Engine

Factory

Manual: Cylinder head, cylinder, exhaust pipe and muffler: remove carbon. Factory: Lubrication chart p.38, periodic inspection chart pp.39-40
Replace spark plugs (two-stroke)

Engine

Factory

Manual: Spark plugs: replace. Factory: Lubrication chart p.38, periodic inspection chart pp.39-40
Check throttle cable(s) free play and return

Fuel and air

Factory

Manual: Throttle grip: grease. Factory: Lubrication chart p.38, periodic inspection chart pp.39-40
Clean fuel tap filter / sediment bowl

Fuel and air

Factory

Manual: Fuel cock: clean fuel strainer. Factory: Lubrication chart p.38, periodic inspection chart pp.39-40: cleaned at 750 and 2,000 mi

Every 6,000 mi or 12 months

4 items

Check charging voltage and regulator / cut-out

Ignition and electrics

Guideline
Check swingarm bushes for play

Rear suspension and frame

Guideline
Inspect rear shocks for leaks and damping

Rear suspension and frame

Guideline
Lubricate speedometer / tachometer cables, check drive

Controls and cables

Guideline

A dry speedo cable whips the needle and eventually kills the instrument.

Every 6,000 mi or 2 years

1 item

Lubricate and check automatic advance unit

Ignition and electrics

Guideline

Every 8,000 mi

3 items

Clean carburetor float bowl(s), check float level and jets

Fuel and air

Factory

Manual: Carburetors: overhaul and clean. Factory: Lubrication chart p.38, periodic inspection chart pp.39-40
Replace air filter element

Fuel and air

Factory

Manual: Air cleaner element: replace. Factory: Lubrication chart p.38, periodic inspection chart pp.39-40
Replace points and condenser

Ignition and electrics

Factory

Manual: Contact points: replace. Factory: Lubrication chart p.38, periodic inspection chart pp.39-40

Every 10,000 mi or 2 years

2 items

Compression test (or leak-down)

Engine

Guideline
Change fork oil

Front end

Guideline

Some early telescopic forks are grease filled or use very small oil quantities. Check your manual.

Every 10,000 mi

1 item

Replace chain and sprockets (wear based)

Final drive

Guideline

Every 15,000 mi or 5 years

1 item

Inspect clutch plates and springs

Primary and gearbox

Guideline

Every 15,000 mi

1 item

Replace brake linings / skim drums (wear based)

Brakes

Guideline

Every 20,000 mi or 2 years

1 item

Replace coolant

Engine

Factory

Manual: Cooling solution: change. Factory: Lubrication chart p.38, periodic inspection chart pp.39-40

Every 20,000 mi or 4 years

2 items

Repack / replace steering head bearings

Front end

Guideline

Many old machines use loose balls in cups and cones. Taper roller conversions are common.
Repack / replace wheel bearings

Wheels and tires

Guideline

Cup-and-cone and taper roller hubs need periodic repacking and adjustment.

Every 25,000 mi or 6 years

1 item

Replace swingarm bushes / bearings

Rear suspension and frame

Guideline

Every 30,000 mi or 6 years

1 item

Rebuild forks: seals, bushes, springs

Front end

Guideline

Every 6 months

1 item

Clean battery terminals, check charge and strap

Ignition and electrics

Guideline

Every 12 months

1 item

Check speedometer / odometer against a known distance

Controls and cables

Guideline

Old speedos drift with tire size and drive wear. Use phone GPS over a measured 10 miles / km.

Every 2 years

5 items

Inspect fuel tank for rust, sealer failure, leaks

Fuel and air

Guideline
Inspect wiring, bullet connectors and ground points

Ignition and electrics

Guideline
Inspect frame, welds and lugs for cracks

Rear suspension and frame

Guideline
Inspect brake hoses; replace old rubber

Brakes

Factory

Manual: Brake and fuel hoses: replace. Factory: Lubrication chart p.38, periodic inspection chart pp.39-40
Replace brake fluid

Brakes

Guideline

Every 4 years

4 items

Inspect coolant hoses and clamps

Engine

Factory

Manual: Radiator hoses: replace. Factory: Lubrication chart p.38, periodic inspection chart pp.39-40
Replace oil injection delivery lines

Engine

Guideline
Replace fuel lines

Fuel and air

Guideline

Old rubber and modern ethanol fuel do not mix well.
Rebuild calipers and master cylinders (seals)

Brakes

Guideline

Every 6 years

2 items

Replace inner tubes and rim tape with tires

Wheels and tires

Guideline
Replace tires on age (regardless of tread)

Wheels and tires

Guideline

Guideline lines: Intervals here are general guidelines for the machine's era and layout, compiled for this app. They are not factory manual figures. Check your workshop manual, and edit any interval in the bike's Schedule tab.