No photo of this model in the library yet.

Have this bike? Send a photo or the manual's service chart

Beta · Shim-adjusted overhead-cam four-stroke, wet sump, gearbox shares engine oil, chain drive

RR 250

Library entry covers 2006-2025

43 factory 52 guideline

Published source

Beta 2018 Owners Manual RR 250-300 Standard & Race Editions, Scheduled maintenance vehicle pp.81-82

Factory owner's handbook. Covers Beta 2018 RR 250-300 two-stroke Standard and Race editions owner's manual (Beta USA); the four-stroke years are not covered.

95 items for a 2008 model, grouped by interval the way a factory chart is laid out.

How this bike is built (what the schedule is based on)

Engine cycle: Four-stroke
Engine lubrication: Wet sump (oil in crankcase)
Oil filtration: Replaceable cartridge or spin-on filter
Valve gear: Overhead cam, shim adjusted (incl. desmo)
Ignition: Electronic (CDI / transistor / ECU)
Charging: Alternator / stator with rectifier
Battery: Wet cell (flooded lead-acid, needs topping up)
Fuel system: Fuel injection
Cooling: Liquid cooled
Primary drive: Gear or chain inside engine, shares engine oil
Gearbox oil: Shares engine oil
Clutch control: Hand lever, cable
Final drive: Chain
Front suspension: Telescopic fork
Rear suspension: Swingarm, single shock / cantilever
Front brake: Disc, hydraulic
Rear brake: Disc, hydraulic
Wheels: Spoked, tubed
Sidecar: No sidecar

Maintenance schedule

2008 Beta RR 250

On the road: every 300 km

1 item

Check engine oil level

Pre-ride / on the road

Guideline

Each fuel stop on old machines. Dry sump: check the tank hot, engine idling or just stopped, per your manual.

On the road: every 500 km

3 items

Check lights, horn, brake light switches

Pre-ride / on the road

Guideline
Check tire pressures

Pre-ride / on the road

Guideline
Lubricate drive chain

Pre-ride / on the road

Guideline

Lube warm, ideally at the end of the riding day so it soaks in overnight. Sooner after rain.

On the road: every 800 km

1 item

Check coolant level

Pre-ride / on the road

Guideline

On the road: every 1,000 km

1 item

Check chain slack and rear wheel alignment

Pre-ride / on the road

Guideline

Every 1,600 km or 6 months

1 item

Inspect tire tread, sidewalls and date codes

Wheels and tires

Guideline

Every 5,000 km or 12 months

10 items

Check throttle cable(s) free play and return

Fuel and air

Guideline
Clean drive chain thoroughly (remove and soak, re-lube)

Final drive

Guideline

Non O-ring chains on old machines: remove, clean, soak in hot chain grease or lube, refit with the master link clip closed end leading.
Inspect chain and sprockets for wear (measure stretch)

Final drive

Guideline
Check steering head bearing adjustment

Front end

Guideline
Inspect fork seals, stanchions and fork boots

Front end

Guideline
Check footrests, pegs, rear brake and gear lever pivots

Rear suspension and frame

Guideline
Grease and check center / side stand and springs

Rear suspension and frame

Guideline
Check brake pads and discs

Brakes

Guideline
Check spoke tension and wheel true

Wheels and tires

Guideline
Check wheel bearings for play

Wheels and tires

Guideline

Every 6,500 km or 12 months

2 items

Inspect, clean and gap spark plugs

Engine

Guideline
Adjust clutch free play, lubricate cable and lever pivot

Primary and gearbox

Guideline

Every 8,000 km or 12 months

2 items

Change engine oil

Engine

Guideline

Pre-1970 machines: many owners run non-detergent or classic-spec oil with no filter, so short intervals matter. Dry sump: drain the tank and the crankcase/sump, flush the tank and clean the feed and return screens.
Replace oil filter

Engine

Guideline

Every 9,500 km or 12 months

7 items

Inspect coolant hoses and clamps

Engine

Guideline
Clean / inspect air filter

Fuel and air

Guideline

Mesh or oiled foam: clean and re-oil. Paper: blow out or replace. Some very early machines have no filter at all.
Check charging voltage and regulator / cut-out

Ignition and electrics

Guideline
Check swingarm bushes for play

Rear suspension and frame

Guideline
Inspect rear shocks for leaks and damping

Rear suspension and frame

Guideline
Lubricate control cables and lever pivots

Controls and cables

Guideline
Lubricate speedometer / tachometer cables, check drive

Controls and cables

Guideline

A dry speedo cable whips the needle and eventually kills the instrument.

Every 16,000 km or 2 years

1 item

Compression test (or leak-down)

Engine

Guideline

Every 19,500 km or 2 years

4 items

Replace air filter element

Fuel and air

Guideline
Synchronize throttle bodies

Fuel and air

Guideline
Clean and grease rear suspension linkage

Rear suspension and frame

Guideline
Grease swingarm pivot

Rear suspension and frame

Guideline

Every 24,000 km or 3 years

1 item

Change fork oil

Front end

Guideline

Some early telescopic forks are grease filled or use very small oil quantities. Check your manual.

Every 24,000 km or 4 years

1 item

Check valve clearances (shim adjusted)

Engine

Guideline

Every 25,500 km or 4 years

1 item

Replace spark plugs

Engine

Guideline

Every 29,000 km

1 item

Replace chain and sprockets (wear based)

Final drive

Guideline

Every 32,000 km or 4 years

2 items

Repack / replace steering head bearings

Front end

Guideline

Many old machines use loose balls in cups and cones. Taper roller conversions are common.
Repack / replace wheel bearings

Wheels and tires

Guideline

Cup-and-cone and taper roller hubs need periodic repacking and adjustment.

Every 38,500 km or 4 years

1 item

Replace fuel filter

Fuel and air

Guideline

Every 40,000 km or 6 years

1 item

Replace swingarm bushes / bearings

Rear suspension and frame

Guideline

Every 48,500 km or 6 years

1 item

Rebuild forks: seals, bushes, springs

Front end

Guideline

Every 30 h

29 items

Bolts (tighten)

Engine

Factory

Factory: Scheduled maintenance vehicle (p.82): T at end of running-in (3 hours), coupon 1 (30 hours), coupon 2 (60 hours), coupon 3 (90 hours), coupon 4 (120 hours), coupon 5 (150 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Breather pipe (check)

Engine

Factory

Factory: Scheduled maintenance vehicle (p.81): C at end of running-in (3 hours), coupon 1 (30 hours), coupon 2 (60 hours), coupon 3 (90 hours), coupon 4 (120 hours), coupon 5 (150 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Coolant system tightness and coolant level (check)

Engine

Factory

Factory: Scheduled maintenance vehicle (p.81): C at end of running-in (3 hours), coupon 1 (30 hours), coupon 2 (60 hours), coupon 3 (90 hours), coupon 4 (120 hours), coupon 5 (150 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Drives sliding and regulation (check)

Engine

Factory

Factory: Scheduled maintenance vehicle (p.81): C at end of running-in (3 hours), coupon 1 (30 hours), coupon 2 (60 hours), coupon 3 (90 hours), coupon 4 (120 hours), coupon 5 (150 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Engine clamping screws (check)

Engine

Factory

Factory: Scheduled maintenance vehicle (p.81): C at end of running-in (3 hours), coupon 1 (30 hours), coupon 2 (60 hours), coupon 3 (90 hours), coupon 4 (120 hours), coupon 5 (150 hours), coupon 6 (180 hours). Starred: medium strength threadlock; engine to chassis special screw M10 45 Nm; head brackets M8 35 Nm (table p.82). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Exhaust manifold tightness (check)

Engine

Factory

Factory: Scheduled maintenance vehicle (p.81): C at end of running-in (3 hours), coupon 1 (30 hours), coupon 2 (60 hours), coupon 3 (90 hours), coupon 4 (120 hours), coupon 5 (150 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Rear suspension linkage (check)

Engine

Factory

Factory: Scheduled maintenance vehicle (p.82): C at end of running-in (3 hours), coupon 1 (30 hours), coupon 2 (60 hours), coupon 3 (90 hours), coupon 4 (120 hours), coupon 5 (150 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Spark plug cap (clean)

Engine

Factory

Factory: Scheduled maintenance vehicle (p.81): P at end of running-in (3 hours), coupon 1 (30 hours), coupon 2 (60 hours), coupon 3 (90 hours), coupon 4 (120 hours), coupon 5 (150 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Airbox and air filter (clean)

Fuel and air

Factory

Factory: Scheduled maintenance vehicle (p.81): P at end of running-in (3 hours), coupon 1 (30 hours), coupon 2 (60 hours), coupon 3 (90 hours), coupon 4 (120 hours), coupon 5 (150 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Carburetor idling setting (check)

Fuel and air

Factory

Factory: Scheduled maintenance vehicle (p.81): C at end of running-in (3 hours), coupon 1 (30 hours), coupon 2 (60 hours), coupon 3 (90 hours), coupon 4 (120 hours), coupon 5 (150 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Carburetor tightness (check)

Fuel and air

Factory

Factory: Scheduled maintenance vehicle (p.81): C at end of running-in (3 hours), coupon 1 (30 hours), coupon 2 (60 hours), coupon 3 (90 hours), coupon 4 (120 hours), coupon 5 (150 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Fuel pipe (check)

Fuel and air

Factory

Factory: Scheduled maintenance vehicle (p.81): C at end of running-in (3 hours), coupon 1 (30 hours), coupon 2 (60 hours), coupon 3 (90 hours), coupon 4 (120 hours), coupon 5 (150 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Clutch pump liquid level (check)

Primary and gearbox

Factory

Factory: Scheduled maintenance vehicle (p.81): C at end of running-in (3 hours), coupon 1 (30 hours), coupon 2 (60 hours), coupon 3 (90 hours), coupon 4 (120 hours), coupon 5 (150 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Clutch springs length (check)

Primary and gearbox

Factory

Factory: Scheduled maintenance vehicle (p.81): C at coupon 1 (30 hours), coupon 2 (60 hours), coupon 4 (120 hours), coupon 5 (150 hours). Also S at coupon 3 (90 hours); S at coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Clutch/bell hub (check)

Primary and gearbox

Factory

Factory: Scheduled maintenance vehicle (p.81): C at coupon 1 (30 hours), coupon 2 (60 hours), coupon 3 (90 hours), coupon 4 (120 hours), coupon 5 (150 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Coated clutch disks (check)

Primary and gearbox

Factory

Factory: Scheduled maintenance vehicle (p.81): C at coupon 1 (30 hours), coupon 2 (60 hours), coupon 4 (120 hours), coupon 5 (150 hours). Also S at coupon 3 (90 hours); S at coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Gear and clutch oil (replace)

Primary and gearbox

Factory

Factory: Scheduled maintenance vehicle (p.81): S at end of running-in (3 hours), coupon 1 (30 hours), coupon 2 (60 hours), coupon 3 (90 hours), coupon 4 (120 hours), coupon 5 (150 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Chain, plate wheel and pinion (check)

Final drive

Factory

Factory: Scheduled maintenance vehicle (p.81): C at end of running-in (3 hours), coupon 1 (30 hours), coupon 2 (60 hours), coupon 3 (90 hours), coupon 4 (120 hours), coupon 5 (150 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Fork cover (clean)

Front end

Factory

Factory: Scheduled maintenance vehicle (p.82): P at end of running-in (3 hours), coupon 1 (30 hours), coupon 2 (60 hours), coupon 3 (90 hours), coupon 4 (120 hours), coupon 5 (150 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Shock absorber and telescopic fork (check)

Front end

Factory

Factory: Scheduled maintenance vehicle (p.82): C at end of running-in (3 hours), coupon 1 (30 hours), coupon 2 (60 hours), coupon 3 (90 hours), coupon 4 (120 hours), coupon 5 (150 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Steering bearings (check)

Front end

Factory

Factory: Scheduled maintenance vehicle (p.82): C at end of running-in (3 hours), coupon 1 (30 hours), coupon 2 (60 hours), coupon 3 (90 hours), coupon 4 (120 hours), coupon 5 (150 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Brake disc thickness (check)

Brakes

Factory

Factory: Scheduled maintenance vehicle (p.82): C at end of running-in (3 hours), coupon 1 (30 hours), coupon 2 (60 hours), coupon 3 (90 hours), coupon 4 (120 hours), coupon 5 (150 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Brake pipe tightness (check)

Brakes

Factory

Factory: Scheduled maintenance vehicle (p.82): C at end of running-in (3 hours), coupon 1 (30 hours), coupon 2 (60 hours), coupon 3 (90 hours), coupon 4 (120 hours), coupon 5 (150 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Brakes: liquid level, pads thickness (check)

Brakes

Factory

Factory: Scheduled maintenance vehicle (p.82): C at end of running-in (3 hours), coupon 1 (30 hours), coupon 2 (60 hours), coupon 3 (90 hours), coupon 4 (120 hours), coupon 5 (150 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Tires, wear and pressure (check)

Wheels and tires

Factory

Factory: Scheduled maintenance vehicle (p.82): C at end of running-in (3 hours), coupon 1 (30 hours), coupon 2 (60 hours), coupon 3 (90 hours), coupon 4 (120 hours), coupon 5 (150 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Wheel bearings clearance (check)

Wheels and tires

Factory

Factory: Scheduled maintenance vehicle (p.82): C at end of running-in (3 hours), coupon 1 (30 hours), coupon 2 (60 hours), coupon 3 (90 hours), coupon 4 (120 hours), coupon 5 (150 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Wheel spokes and rim coaxiality (check)

Wheels and tires

Factory

Factory: Scheduled maintenance vehicle (p.82): C at end of running-in (3 hours), coupon 1 (30 hours), coupon 2 (60 hours), coupon 3 (90 hours), coupon 4 (120 hours), coupon 5 (150 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Idle travel levers and drives sliding (check)

Controls and cables

Factory

Factory: Scheduled maintenance vehicle (p.82): C at end of running-in (3 hours), coupon 1 (30 hours), coupon 2 (60 hours), coupon 3 (90 hours), coupon 4 (120 hours), coupon 5 (150 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Kick start and gearchange lever screws (check)

Controls and cables

Factory

Factory: Scheduled maintenance vehicle (p.81): C at end of running-in (3 hours), coupon 1 (30 hours), coupon 2 (60 hours), coupon 3 (90 hours), coupon 4 (120 hours), coupon 5 (150 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.

Every 60 h

4 items

Cylinder (check)

Engine

Factory

Factory: Scheduled maintenance vehicle (p.81): C at coupon 2 (60 hours), coupon 4 (120 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Piston and segments (replace)

Engine

Factory

Factory: Scheduled maintenance vehicle (p.81): S at coupon 2 (60 hours), coupon 4 (120 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Reed valve (check)

Engine

Factory

Factory: Scheduled maintenance vehicle (p.81): C at coupon 2 (60 hours), coupon 4 (120 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Spark plug (replace)

Engine

Factory

Factory: Scheduled maintenance vehicle (p.81): S at coupon 2 (60 hours), coupon 4 (120 hours), coupon 6 (180 hours). Also C at end of running-in (3 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.

Every 90 h

8 items

Connecting rod (replace)

Engine

Factory

Factory: Scheduled maintenance vehicle (p.81): S at coupon 3 (90 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Drive shaft bearings (replace)

Engine

Factory

Factory: Scheduled maintenance vehicle (p.81): S at coupon 3 (90 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Exhaust valve (check, clean)

Engine

Factory

Factory: Scheduled maintenance vehicle (p.81): C/P at coupon 2 (60 hours), coupon 5 (150 hours). Printed at 60 and 150 hours. Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Water pump oil seal (replace)

Engine

Factory

Factory: Scheduled maintenance vehicle (p.81): S at coupon 3 (90 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Clutch springs (replace)

Primary and gearbox

Factory

Factory: Scheduled maintenance vehicle (p.81): S at coupon 3 (90 hours), coupon 6 (180 hours). Also C at coupon 1 (30 hours); C at coupon 2 (60 hours); C at coupon 4 (120 hours); C at coupon 5 (150 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Coated clutch disks (replace)

Primary and gearbox

Factory

Factory: Scheduled maintenance vehicle (p.81): S at coupon 3 (90 hours), coupon 6 (180 hours). Also C at coupon 1 (30 hours); C at coupon 2 (60 hours); C at coupon 4 (120 hours); C at coupon 5 (150 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Gearbox bearing, drive shaft side (replace)

Primary and gearbox

Factory

Factory: Scheduled maintenance vehicle (p.81): S at coupon 3 (90 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Surface appearance of the gearbox (check)

Primary and gearbox

Factory

Factory: Scheduled maintenance vehicle (p.81): C at coupon 3 (90 hours), coupon 6 (180 hours). Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.

Every 6 months

1 item

Clean battery terminals, check charge and strap

Ignition and electrics

Guideline

Every 2 years

4 items

Replace coolant

Engine

Guideline
Inspect wiring, bullet connectors and ground points

Ignition and electrics

Guideline
Inspect frame, welds and lugs for cracks

Rear suspension and frame

Guideline
Replace brake fluid

Brakes

Guideline

Every 4 years

3 items

Replace fuel lines

Fuel and air

Guideline

Old rubber and modern ethanol fuel do not mix well.
Inspect brake hoses; replace old rubber

Brakes

Guideline
Rebuild calipers and master cylinders (seals)

Brakes

Guideline

Every 6 years

2 items

Replace inner tubes and rim tape with tires

Wheels and tires

Guideline
Replace tires on age (regardless of tread)

Wheels and tires

Guideline

No interval set

2 items

Head screws (tighten)

Engine

Factory

Factory: Scheduled maintenance vehicle (p.81): T at end of running-in (3 hours). End of running-in only. Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.
Spark plug (check)

Engine

Factory

Factory: Scheduled maintenance vehicle (p.81): C at end of running-in (3 hours). Also S at coupon 2 (60 hours); S at coupon 4 (120 hours); S at coupon 6 (180 hours). Checked only at the end of running-in. Key: C = check (clean, adjust, lubricate, replace as necessary); S = replace/renew; R = adjust; P = clean; T = tighten. For any service requirements, contact Betamotor's Authorized Service Network.

Guideline lines: Intervals here are general guidelines for the machine's era and layout, compiled for this app. They are not factory manual figures. Check your workshop manual, and edit any interval in the bike's Schedule tab.