Have this bike? Send a photo or the manual's service chart

BSA · Triumph Trident / BSA Rocket 3 (1968-1976)

Rocket 3

Library entry covers 1968-1972

13 factory 56 guideline

Published source

BSA A75 Rocket 3 Workshop Manual (BSA), Lubrication Section A, Routine Maintenance p.A.2

Factory workshop manual. Covers BSA A75 Rocket 3 workshop manual (750 cc model); intervals in miles and km.

Open the source

69 items for a 1970 model, grouped by interval the way a factory chart is laid out.

How this bike is built (what the schedule is based on)

Engine cycle: Four-stroke
Engine lubrication: Dry sump (separate oil tank)
Oil filtration: Replaceable cartridge or spin-on filter
Valve gear: Overhead valve, pushrods, adjustable tappets
Ignition: Battery and coil with contact points
Charging: Alternator / stator with rectifier
Battery: Wet cell (flooded lead-acid, needs topping up)
Fuel system: Two or more carburetors
Cooling: Air / oil cooled
Primary drive: Chain in oil-bath case with its own oil
Gearbox oil: Separate gearbox oil
Clutch control: Hand lever, cable
Final drive: Chain
Front suspension: Telescopic fork
Rear suspension: Swingarm, twin shocks
Front brake: Drum (or band / stirrup)
Rear brake: Drum (or band / belt rim)
Wheels: Spoked, tubed
Sidecar: No sidecar

Maintenance schedule

1970 BSA Rocket 3

On the road: every 200 mi

1 item

Check engine oil level

Pre-ride / on the road

Guideline

Each fuel stop on old machines. Dry sump: check the tank hot, engine idling or just stopped, per your manual.

On the road: every 300 mi

3 items

Check lights, horn, brake light switches

Pre-ride / on the road

Guideline
Check tire pressures

Pre-ride / on the road

Guideline
Lubricate drive chain

Pre-ride / on the road

Guideline

Lube warm, ideally at the end of the riding day so it soaks in overnight. Sooner after rain.

On the road: every 500 mi

1 item

Walk-around: check nuts and bolts for vibration loosening

Pre-ride / on the road

Guideline

Old machines shake things loose: exhaust nuts, mudguard stays, footrests, tank mounts, battery strap.

On the road: every 600 mi

1 item

Check chain slack and rear wheel alignment

Pre-ride / on the road

Guideline

On the road: every 1,000 mi

1 item

Check road kit: plugs, points file, master link, tube patches, wire, tape

Pre-ride / on the road

Guideline

Every 1,000 mi or 1 month

1 item

Check battery electrolyte, top up with distilled water

Ignition and electrics

Guideline

Wet-cell batteries on old machines need regular topping up, more in hot weather.

Every 1,000 mi or 6 months

3 items

Adjust front drum brake

Brakes

Guideline
Adjust rear drum brake and rod / cable linkage

Brakes

Guideline
Inspect tire tread, sidewalls and date codes

Wheels and tires

Guideline

Every 1,500 mi or 12 months

1 item

Adjust clutch free play, lubricate cable and lever pivot

Primary and gearbox

Guideline

Every 2,000 mi or 12 months

1 item

Inspect, clean and gap spark plugs

Engine

Guideline

Every 2,000 mi

7 items

Clean and gap contact breaker points, oil cam felt

Ignition and electrics

Factory

Manual: Contact breaker cam: lubricate. Factory: Routine maintenance p.A.2, front forks p.A.11
Lubricate and check automatic advance unit

Ignition and electrics

Factory

Manual: Auto-advance unit: lubricate. Factory: Routine maintenance p.A.2, front forks p.A.11
Check gearbox oil level

Primary and gearbox

Factory

Manual: Gearbox oil level: check. Factory: Routine maintenance p.A.2, front forks p.A.11: primary case level checked at the same interval
Clean drive chain thoroughly (remove and soak, re-lube)

Final drive

Factory

Manual: Rear chain: lubricate. Factory: Routine maintenance p.A.2, front forks p.A.11
Grease and check center / side stand and springs

Rear suspension and frame

Factory

Manual: Brake pedal pivot: grease; central stand: grease. Factory: Routine maintenance p.A.2, front forks p.A.11: central stand every 4,000 mi
Grease swingarm pivot

Rear suspension and frame

Factory

Manual: Swinging arm pivot: grease. Factory: Routine maintenance p.A.2, front forks p.A.11
Lubricate control cables and lever pivots

Controls and cables

Factory

Manual: Exposed cables and joints: lubricate. Factory: Routine maintenance p.A.2, front forks p.A.11: carburetor linkage oiled weekly or every 250 mi

Every 3,000 mi or 12 months

16 items

Check and adjust valve clearances

Engine

Guideline
Check engine mounting bolts and plates

Engine

Guideline
Check throttle cable(s) free play and return

Fuel and air

Guideline
Clean / inspect air filter

Fuel and air

Guideline

Mesh or oiled foam: clean and re-oil. Paper: blow out or replace. Some very early machines have no filter at all.
Clean fuel tap filter / sediment bowl

Fuel and air

Guideline
Synchronize carburetors

Fuel and air

Guideline
Check / set ignition timing

Ignition and electrics

Guideline
Adjust clutch pushrod / clutch adjuster

Primary and gearbox

Guideline
Check chain guard, chain oiler (if fitted), rear chain case

Final drive

Guideline
Inspect chain and sprockets for wear (measure stretch)

Final drive

Guideline
Check steering damper (friction or hydraulic)

Front end

Guideline
Check steering head bearing adjustment

Front end

Guideline
Inspect fork seals, stanchions and fork boots

Front end

Guideline
Check footrests, pegs, rear brake and gear lever pivots

Rear suspension and frame

Guideline
Check spoke tension and wheel true

Wheels and tires

Guideline
Check wheel bearings for play

Wheels and tires

Guideline

Every 4,000 mi or 12 months

1 item

Replace spark plugs

Engine

Guideline

Every 4,000 mi

5 items

Change engine oil

Engine

Factory

Manual: Oil tank: drain and refill; clean oil tank filter and crankcase sump filter. Factory: Routine maintenance p.A.2, front forks p.A.11: oil level checked weekly or every 250 mi; primary case drained at every engine oil change (p.A.11)
Replace oil filter

Engine

Factory

Manual: Full-flow oil filter: replace. Factory: Routine maintenance p.A.2, front forks p.A.11
Change gearbox oil

Primary and gearbox

Factory

Manual: Gearbox: drain and refill. Factory: Routine maintenance p.A.2, front forks p.A.11
Change primary chaincase oil

Primary and gearbox

Factory

Manual: Primary case: drain and refill. Factory: Routine maintenance p.A.2, front forks p.A.11
Lubricate brake cam spindles, check linings and drums

Brakes

Factory

Manual: Brake cam spindles: grease. Factory: Routine maintenance p.A.2, front forks p.A.11

Every 5,000 mi or 12 months

1 item

Check / adjust primary chain

Primary and gearbox

Guideline

Every 5,000 mi or 2 years

1 item

Check cylinder head bolt torque

Engine

Guideline

Air-cooled iron and alloy engines can lose head bolt tension; follow your manual's sequence and whether it is done hot or cold.

Every 6,000 mi or 12 months

5 items

Clean carburetor float bowl(s), check float level and jets

Fuel and air

Guideline

Ethanol fuel varnishes old carbs quickly in storage.
Check charging voltage and regulator / cut-out

Ignition and electrics

Guideline
Check swingarm bushes for play

Rear suspension and frame

Guideline
Inspect rear shocks for leaks and damping

Rear suspension and frame

Guideline
Lubricate speedometer / tachometer cables, check drive

Controls and cables

Guideline

A dry speedo cable whips the needle and eventually kills the instrument.

Every 6,000 mi or 2 years

1 item

Check engine breather and oil return

Engine

Guideline

Every 10,000 mi or 2 years

1 item

Compression test (or leak-down)

Engine

Guideline

Every 10,000 mi

2 items

Replace chain and sprockets (wear based)

Final drive

Guideline
Change fork oil

Front end

Factory

Manual: Front forks: change oil. Factory: Routine maintenance p.A.2, front forks p.A.11: p.A.11

Every 12,000 mi or 2 years

1 item

Replace air filter element

Fuel and air

Guideline

Every 12,000 mi or 3 years

1 item

Replace points and condenser

Ignition and electrics

Guideline

Every 15,000 mi or 5 years

1 item

Inspect clutch plates and springs

Primary and gearbox

Guideline

Every 15,000 mi

1 item

Replace brake linings / skim drums (wear based)

Brakes

Guideline

Every 20,000 mi or 4 years

2 items

Repack / replace steering head bearings

Front end

Guideline

Many old machines use loose balls in cups and cones. Taper roller conversions are common.
Repack / replace wheel bearings

Wheels and tires

Guideline

Cup-and-cone and taper roller hubs need periodic repacking and adjustment.

Every 25,000 mi or 6 years

1 item

Replace swingarm bushes / bearings

Rear suspension and frame

Guideline

Every 30,000 mi or 6 years

1 item

Rebuild forks: seals, bushes, springs

Front end

Guideline

Every 6 months

1 item

Clean battery terminals, check charge and strap

Ignition and electrics

Guideline

Every 12 months

1 item

Check speedometer / odometer against a known distance

Controls and cables

Guideline

Old speedos drift with tire size and drive wear. Use phone GPS over a measured 10 miles / km.

Every 2 years

3 items

Inspect fuel tank for rust, sealer failure, leaks

Fuel and air

Guideline
Inspect wiring, bullet connectors and ground points

Ignition and electrics

Guideline
Inspect frame, welds and lugs for cracks

Rear suspension and frame

Guideline

Every 4 years

1 item

Replace fuel lines

Fuel and air

Guideline

Old rubber and modern ethanol fuel do not mix well.

Every 6 years

2 items

Replace inner tubes and rim tape with tires

Wheels and tires

Guideline
Replace tires on age (regardless of tread)

Wheels and tires

Guideline

Guideline lines: Intervals here are general guidelines for the machine's era and layout, compiled for this app. They are not factory manual figures. Check your workshop manual, and edit any interval in the bike's Schedule tab.