Honda · Honda Gold Wing GL1000 / GL1100 / GL1200 (1975-1987)

VF / Sabre / Magna / Interceptor V4

Library entry covers 1982-1990

23 factory 40 guideline

Published source

Honda V45 Sabre / Magna Shop Manual (Honda Motor Co.), Maintenance Schedule V45 Sabre-VF750S p.3-3

Factory service manual. Covers 1982 V45 Sabre VF750S shop manual (issued October 1982); chart in mi, km and months.

Open the source

63 items for a 1982 model, grouped by interval the way a factory chart is laid out.

How this bike is built (what the schedule is based on)

Engine cycle: Four-stroke
Engine lubrication: Wet sump (oil in crankcase)
Oil filtration: Replaceable cartridge or spin-on filter
Valve gear: Overhead cam, screw/locknut adjusters
Ignition: Electronic (CDI / transistor / ECU)
Charging: Alternator / stator with rectifier
Battery: Wet cell (flooded lead-acid, needs topping up)
Fuel system: Two or more carburetors
Cooling: Liquid cooled
Primary drive: Gear or chain inside engine, shares engine oil
Gearbox oil: Shares engine oil
Clutch control: Hand lever, cable
Final drive: Shaft
Front suspension: Telescopic fork
Rear suspension: Swingarm, single shock / cantilever
Front brake: Disc, hydraulic
Rear brake: Disc, hydraulic
Wheels: Cast / alloy, tubeless
Sidecar: No sidecar

Maintenance schedule

1982 Honda VF / Sabre / Magna / Interceptor V4

On the road: every 200 mi

1 item

Check engine oil level

Pre-ride / on the road

Guideline

Each fuel stop on old machines. Dry sump: check the tank hot, engine idling or just stopped, per your manual.

On the road: every 300 mi

2 items

Check lights, horn, brake light switches

Pre-ride / on the road

Guideline
Check tire pressures

Pre-ride / on the road

Guideline

On the road: every 500 mi

1 item

Check coolant level

Pre-ride / on the road

Guideline

On the road: every 1,000 mi

1 item

Check road kit: plugs, points file, master link, tube patches, wire, tape

Pre-ride / on the road

Guideline

On the road: every 8,000 mi

1 item

Walk-around: check nuts and bolts for vibration loosening

Pre-ride / on the road

Factory

Manual: Nuts, bolts, fasteners: inspect. Factory: Maintenance schedule p.3-3: first at 600 mi

Every 1,000 mi or 6 months

1 item

Inspect tire tread, sidewalls and date codes

Wheels and tires

Guideline

Every 1,500 mi or 12 months

1 item

Adjust clutch free play, lubricate cable and lever pivot

Primary and gearbox

Guideline

Every 2,000 mi or 12 months

3 items

Inspect, clean and gap spark plugs

Engine

Guideline
Grease swingarm pivot

Rear suspension and frame

Guideline
Lubricate control cables and lever pivots

Controls and cables

Guideline

Every 3,000 mi or 12 months

7 items

Check engine mounting bolts and plates

Engine

Guideline
Clean fuel tap filter / sediment bowl

Fuel and air

Guideline
Adjust clutch pushrod / clutch adjuster

Primary and gearbox

Guideline
Check steering damper (friction or hydraulic)

Front end

Guideline
Inspect fork seals, stanchions and fork boots

Front end

Guideline
Check footrests, pegs, rear brake and gear lever pivots

Rear suspension and frame

Guideline
Check wheel bearings for play

Wheels and tires

Guideline

Every 4,000 mi or 1 month

1 item

Check battery electrolyte, top up with distilled water

Ignition and electrics

Factory

Manual: Battery: inspect. Factory: Maintenance schedule p.3-3: first at 600 mi

Every 4,000 mi

4 items

Check engine breather and oil return

Engine

Factory

Manual: Crankcase breather: clean. Factory: Maintenance schedule p.3-3: more often in rain or at full throttle
Replace spark plugs

Engine

Factory

Manual: Spark plugs: replace. Factory: Maintenance schedule p.3-3
Clean / inspect air filter

Fuel and air

Factory

Manual: Air cleaner: clean. Factory: Maintenance schedule p.3-3: more often in dusty areas
Check brake pads and discs

Brakes

Factory

Manual: Brake pad wear: inspect. Factory: Maintenance schedule p.3-3

Every 6,000 mi or 12 months

5 items

Clean carburetor float bowl(s), check float level and jets

Fuel and air

Guideline

Ethanol fuel varnishes old carbs quickly in storage.
Check charging voltage and regulator / cut-out

Ignition and electrics

Guideline
Check final drive for leaks and bearing play

Final drive

Guideline
Check swingarm bushes for play

Rear suspension and frame

Guideline
Lubricate speedometer / tachometer cables, check drive

Controls and cables

Guideline

A dry speedo cable whips the needle and eventually kills the instrument.

Every 8,000 mi or 12 months

2 items

Change engine oil

Engine

Factory

Manual: Engine oil: replace. Factory: Maintenance schedule p.3-3: first at 600 mi
Replace oil filter

Engine

Factory

Manual: Engine oil filter: replace. Factory: Maintenance schedule p.3-3: first at 600 mi

Every 8,000 mi

11 items

Check and adjust valve clearances

Engine

Factory

Manual: Valve clearance: inspect, adjust. Factory: Maintenance schedule p.3-3: first at 600 mi; dealer item
Inspect coolant hoses and clamps

Engine

Factory

Manual: Cooling system hoses and connections: inspect. Factory: Maintenance schedule p.3-3: first at 600 mi
Check throttle cable(s) free play and return

Fuel and air

Factory

Manual: Throttle operation: inspect. Factory: Maintenance schedule p.3-3: first at 600 mi; carburetor choke inspected at the same interval
Replace fuel lines

Fuel and air

Factory

Manual: Fuel lines: inspect. Factory: Maintenance schedule p.3-3: dealer item
Synchronize carburetors

Fuel and air

Factory

Manual: Carburetor synchronization: inspect. Factory: Maintenance schedule p.3-3: dealer item; idle speed inspected every 4,000 mi (6,400 km), first at 600 mi
Lubricate drive shaft splines / check U-joint

Final drive

Factory

Manual: Final driven flange: lubricate. Factory: Maintenance schedule p.3-3: or at each rear tire change
Check steering head bearing adjustment

Front end

Factory

Manual: Steering head bearings: inspect. Factory: Maintenance schedule p.3-3: first at 600 mi; Honda recommends dealer service
Grease and check center / side stand and springs

Rear suspension and frame

Factory

Manual: Side stand: inspect. Factory: Maintenance schedule p.3-3
Inspect rear shocks for leaks and damping

Rear suspension and frame

Factory

Manual: Suspension: inspect. Factory: Maintenance schedule p.3-3: first at 600 mi; dealer item
Adjust rear drum brake and rod / cable linkage

Brakes

Factory

Manual: Brake system: inspect. Factory: Maintenance schedule p.3-3: first at 600 mi; brake light switch and headlight aim at the same interval
Check spoke tension and wheel true

Wheels and tires

Factory

Manual: Wheels: inspect. Factory: Maintenance schedule p.3-3: first at 600 mi; Honda recommends dealer service

Every 10,000 mi or 2 years

2 items

Compression test (or leak-down)

Engine

Guideline
Change fork oil

Front end

Guideline

Some early telescopic forks are grease filled or use very small oil quantities. Check your manual.

Every 12,000 mi or 2 years

2 items

Replace air filter element

Fuel and air

Guideline
Clean and grease rear suspension linkage

Rear suspension and frame

Guideline

Every 15,000 mi or 5 years

1 item

Inspect clutch plates and springs

Primary and gearbox

Guideline

Every 20,000 mi or 4 years

2 items

Repack / replace steering head bearings

Front end

Guideline

Many old machines use loose balls in cups and cones. Taper roller conversions are common.
Repack / replace wheel bearings

Wheels and tires

Guideline

Cup-and-cone and taper roller hubs need periodic repacking and adjustment.

Every 24,000 mi or 2 years

2 items

Replace hydraulic clutch fluid

Primary and gearbox

Factory

Manual: Clutch fluid: replace. Factory: Maintenance schedule p.3-3: inspected monthly and every 4,000 mi; clutch system inspected every 8,000 mi
Replace brake fluid

Brakes

Factory

Manual: Brake fluid (front): replace. Factory: Maintenance schedule p.3-3: inspected monthly and every 4,000 mi

Every 24,000 mi

2 items

Replace coolant

Engine

Factory

Manual: Radiator coolant: replace. Factory: Maintenance schedule p.3-3: inspected every 8,000 mi; radiator core inspected at the same interval
Change final drive (rear drive) oil

Final drive

Factory

Manual: Final drive oil: replace. Factory: Maintenance schedule p.3-3: level inspected every 8,000 mi

Every 25,000 mi or 6 years

1 item

Replace swingarm bushes / bearings

Rear suspension and frame

Guideline

Every 30,000 mi or 5 years

1 item

Replace cam timing belts

Engine

Guideline

Age matters as much as miles on old timing belts. A snapped belt bends valves.

Every 30,000 mi or 6 years

1 item

Rebuild forks: seals, bushes, springs

Front end

Guideline

Every 6 months

1 item

Clean battery terminals, check charge and strap

Ignition and electrics

Guideline

Every 12 months

1 item

Check speedometer / odometer against a known distance

Controls and cables

Guideline

Old speedos drift with tire size and drive wear. Use phone GPS over a measured 10 miles / km.

Every 2 years

3 items

Inspect fuel tank for rust, sealer failure, leaks

Fuel and air

Guideline
Inspect wiring, bullet connectors and ground points

Ignition and electrics

Guideline
Inspect frame, welds and lugs for cracks

Rear suspension and frame

Guideline

Every 4 years

2 items

Inspect brake hoses; replace old rubber

Brakes

Guideline
Rebuild calipers and master cylinders (seals)

Brakes

Guideline

Every 6 years

1 item

Replace tires on age (regardless of tread)

Wheels and tires

Guideline

Guideline lines: Intervals here are general guidelines for the machine's era and layout, compiled for this app. They are not factory manual figures. Check your workshop manual, and edit any interval in the bike's Schedule tab.