Honda · Honda XL / XR / SL four-stroke single (1970-)

XL250 / XL350 / XL500 / XR

Library entry covers 1972-1990

18 factory 49 guideline

Published source

Honda XL250S 1978 Owner's Manual (Honda Motor Co.), Maintenance Schedule pp.39-40

Factory owner's handbook. Covers 1978 XL250S owner's manual (US).

Open the source

67 items for a 1975 model, grouped by interval the way a factory chart is laid out.

How this bike is built (what the schedule is based on)

Engine cycle: Four-stroke
Engine lubrication: Wet sump (oil in crankcase)
Oil filtration: Centrifugal (slinger / rotor) filter
Valve gear: Overhead cam, screw/locknut adjusters
Ignition: Magneto (incl. magdyno, flywheel magneto)
Charging: Alternator / stator with rectifier
Battery: Wet cell (flooded lead-acid, needs topping up)
Fuel system: Single carburetor
Cooling: Air / oil cooled
Primary drive: Gear or chain inside engine, shares engine oil
Gearbox oil: Shares engine oil
Clutch control: Hand lever, cable
Final drive: Chain
Front suspension: Telescopic fork
Rear suspension: Swingarm, twin shocks
Front brake: Drum (or band / stirrup)
Rear brake: Drum (or band / belt rim)
Wheels: Spoked, tubed
Sidecar: No sidecar

Maintenance schedule

1975 Honda XL250 / XL350 / XL500 / XR

On the road: every 200 mi

1 item

Check engine oil level

Pre-ride / on the road

Guideline

Each fuel stop on old machines. Dry sump: check the tank hot, engine idling or just stopped, per your manual.

On the road: every 300 mi

2 items

Check lights, horn, brake light switches

Pre-ride / on the road

Guideline
Check tire pressures

Pre-ride / on the road

Guideline

On the road: every 500 mi

1 item

Walk-around: check nuts and bolts for vibration loosening

Pre-ride / on the road

Guideline

Old machines shake things loose: exhaust nuts, mudguard stays, footrests, tank mounts, battery strap.

On the road: every 600 mi

2 items

Check chain slack and rear wheel alignment

Pre-ride / on the road

Guideline
Lubricate drive chain

Pre-ride / on the road

Factory

Manual: Drive chain: inspect. Factory: Maintenance schedule pp.39-40: every 600 mi (1,000 km); initial at 200 mi

On the road: every 1,000 mi

1 item

Check road kit: plugs, points file, master link, tube patches, wire, tape

Pre-ride / on the road

Guideline

Every 1,000 mi or 6 months

1 item

Inspect tire tread, sidewalls and date codes

Wheels and tires

Guideline

Every 1,500 mi or 6 months

1 item

Clean drive chain thoroughly (remove and soak, re-lube)

Final drive

Guideline

Non O-ring chains on old machines: remove, clean, soak in hot chain grease or lube, refit with the master link clip closed end leading.

Every 1,800 mi or 12 months

1 item

Change engine oil

Engine

Factory

Manual: Engine oil: replace. Factory: Maintenance schedule pp.39-40: every 1,800 mi (3,000 km) or every year

Every 2,000 mi or 12 months

2 items

Grease swingarm pivot

Rear suspension and frame

Guideline
Lubricate control cables and lever pivots

Controls and cables

Guideline

Every 3,000 mi or 12 months

11 items

Check engine mounting bolts and plates

Engine

Guideline
Clean fuel tap filter / sediment bowl

Fuel and air

Guideline
Check / set ignition timing

Ignition and electrics

Guideline
Clean and gap contact breaker points, oil cam felt

Ignition and electrics

Guideline
Adjust clutch pushrod / clutch adjuster

Primary and gearbox

Guideline
Check chain guard, chain oiler (if fitted), rear chain case

Final drive

Guideline
Inspect chain and sprockets for wear (measure stretch)

Final drive

Guideline
Check steering damper (friction or hydraulic)

Front end

Guideline
Inspect fork seals, stanchions and fork boots

Front end

Guideline
Check footrests, pegs, rear brake and gear lever pivots

Rear suspension and frame

Guideline
Check wheel bearings for play

Wheels and tires

Guideline

Every 3,600 mi or 1 month

1 item

Check battery electrolyte, top up with distilled water

Ignition and electrics

Factory

Manual: Battery: inspect. Factory: Maintenance schedule pp.39-40: every month or every 3,600 mi

Every 3,600 mi

12 items

Check and adjust valve clearances

Engine

Factory

Manual: Valve clearance: inspect. Factory: Maintenance schedule pp.39-40: dealer item; first at 600 mi
Check engine breather and oil return

Engine

Factory

Manual: Crankcase breather: clean. Factory: Maintenance schedule pp.39-40: more often in rain or at full throttle
Inspect, clean and gap spark plugs

Engine

Factory

Manual: Spark plug: inspect. Factory: Maintenance schedule pp.39-40
Check throttle cable(s) free play and return

Fuel and air

Factory

Manual: Throttle operation: inspect. Factory: Maintenance schedule pp.39-40: dealer item; fuel lines inspected at the same interval
Clean / inspect air filter

Fuel and air

Factory

Manual: Air cleaner: clean. Factory: Maintenance schedule pp.39-40: more often in dusty areas
Adjust clutch free play, lubricate cable and lever pivot

Primary and gearbox

Factory

Manual: Clutch free play: inspect. Factory: Maintenance schedule pp.39-40: first at 600 mi
Grease and check center / side stand and springs

Rear suspension and frame

Factory

Manual: Side stand: inspect. Factory: Maintenance schedule pp.39-40
Inspect rear shocks for leaks and damping

Rear suspension and frame

Factory

Manual: Suspension: inspect. Factory: Maintenance schedule pp.39-40: dealer item; more often off-road
Adjust front drum brake

Brakes

Factory

Manual: Brake system: inspect. Factory: Maintenance schedule pp.39-40: first at 600 mi
Adjust rear drum brake and rod / cable linkage

Brakes

Factory

Manual: Brake system: inspect. Factory: Maintenance schedule pp.39-40: first at 600 mi
Replace brake linings / skim drums (wear based)

Brakes

Factory

Manual: Brake shoe wear: inspect. Factory: Maintenance schedule pp.39-40
Check spoke tension and wheel true

Wheels and tires

Factory

Manual: Wheels/spokes: inspect. Factory: Maintenance schedule pp.39-40: dealer only; more often off-road

Every 4,000 mi or 12 months

1 item

Lubricate brake cam spindles, check linings and drums

Brakes

Guideline

Every 5,000 mi or 2 years

1 item

Check cylinder head bolt torque

Engine

Guideline

Air-cooled iron and alloy engines can lose head bolt tension; follow your manual's sequence and whether it is done hot or cold.

Every 6,000 mi or 12 months

4 items

Clean carburetor float bowl(s), check float level and jets

Fuel and air

Guideline

Ethanol fuel varnishes old carbs quickly in storage.
Check charging voltage and regulator / cut-out

Ignition and electrics

Guideline
Check swingarm bushes for play

Rear suspension and frame

Guideline
Lubricate speedometer / tachometer cables, check drive

Controls and cables

Guideline

A dry speedo cable whips the needle and eventually kills the instrument.

Every 6,000 mi or 2 years

3 items

Clean centrifugal oil filter (rotor / slinger)

Engine

Guideline
Lubricate and check automatic advance unit

Ignition and electrics

Guideline
Magneto: clean slip ring and pickup brush, check HT lead

Ignition and electrics

Guideline

Every 7,200 mi

3 items

Clean oil strainers / mesh screens

Engine

Factory

Manual: Engine oil filter screen: clean. Factory: Maintenance schedule pp.39-40: dealer item
Replace spark plugs

Engine

Factory

Manual: Spark plug: replace. Factory: Maintenance schedule pp.39-40
Check steering head bearing adjustment

Front end

Factory

Manual: Steering head bearing: inspect. Factory: Maintenance schedule pp.39-40: dealer only; first at 600 mi

Every 10,000 mi or 2 years

2 items

Compression test (or leak-down)

Engine

Guideline
Change fork oil

Front end

Guideline

Some early telescopic forks are grease filled or use very small oil quantities. Check your manual.

Every 10,000 mi

1 item

Replace chain and sprockets (wear based)

Final drive

Guideline

Every 12,000 mi or 2 years

1 item

Replace air filter element

Fuel and air

Guideline

Every 12,000 mi or 3 years

1 item

Replace points and condenser

Ignition and electrics

Guideline

Every 15,000 mi or 5 years

1 item

Inspect clutch plates and springs

Primary and gearbox

Guideline

Every 20,000 mi or 4 years

2 items

Repack / replace steering head bearings

Front end

Guideline

Many old machines use loose balls in cups and cones. Taper roller conversions are common.
Repack / replace wheel bearings

Wheels and tires

Guideline

Cup-and-cone and taper roller hubs need periodic repacking and adjustment.

Every 25,000 mi or 6 years

1 item

Replace swingarm bushes / bearings

Rear suspension and frame

Guideline

Every 25,000 mi or 10 years

1 item

Magneto overhaul / re-magnetize, replace capacitor

Ignition and electrics

Guideline

Weak spark when hot is the classic symptom. Old capacitors fail with age, not miles.

Every 30,000 mi or 6 years

1 item

Rebuild forks: seals, bushes, springs

Front end

Guideline

Every 6 months

1 item

Clean battery terminals, check charge and strap

Ignition and electrics

Guideline

Every 12 months

1 item

Check speedometer / odometer against a known distance

Controls and cables

Guideline

Old speedos drift with tire size and drive wear. Use phone GPS over a measured 10 miles / km.

Every 2 years

3 items

Inspect fuel tank for rust, sealer failure, leaks

Fuel and air

Guideline
Inspect wiring, bullet connectors and ground points

Ignition and electrics

Guideline
Inspect frame, welds and lugs for cracks

Rear suspension and frame

Guideline

Every 4 years

1 item

Replace fuel lines

Fuel and air

Guideline

Old rubber and modern ethanol fuel do not mix well.

Every 6 years

2 items

Replace inner tubes and rim tape with tires

Wheels and tires

Guideline
Replace tires on age (regardless of tread)

Wheels and tires

Guideline

Guideline lines: Intervals here are general guidelines for the machine's era and layout, compiled for this app. They are not factory manual figures. Check your workshop manual, and edit any interval in the bike's Schedule tab.