MotoService Log
No photo of this model in the library yet.

Have this bike? Send a photo or the manual's service chart

Husqvarna · Shim-adjusted overhead-cam four-stroke, wet sump, gearbox shares engine oil, chain drive

FX 350

Library entry covers 2017-2025

51 factory 52 guideline

Published source

Husqvarna Owner's Manual 2022 FC 350 FX 350 (3402534en), Service schedule pp.35-37 (ManualsLib 3888547)

Factory source. Covers Husqvarna Owner's Manual 2022 FC 350 / FX 350 (3402534en); one model-year edition for the 2017-2025 row.

103 items for a 2019 model, grouped by interval the way a factory chart is laid out.

How this bike is built (what the schedule is based on)
Engine cycle
Four-stroke
Engine lubrication
Wet sump (oil in crankcase)
Oil filtration
Replaceable cartridge or spin-on filter
Valve gear
Overhead cam, shim adjusted (incl. desmo)
Ignition
Electronic (CDI / transistor / ECU)
Charging
Alternator / stator with rectifier
Battery
Wet cell (flooded lead-acid, needs topping up)
Fuel system
Fuel injection
Cooling
Liquid cooled
Primary drive
Gear or chain inside engine, shares engine oil
Gearbox oil
Shares engine oil
Clutch control
Hand lever, hydraulic
Final drive
Chain
Front suspension
Telescopic fork
Rear suspension
Swingarm, single shock / cantilever
Front brake
Disc, hydraulic
Rear brake
Disc, hydraulic
Wheels
Spoked, tubed
Sidecar
No sidecar
Maintenance schedule

2019 Husqvarna FX 350

On the road: every 300 km

1 item
  • Check engine oil level
    Pre-ride / on the road
    Guideline

    Each fuel stop on old machines. Dry sump: check the tank hot, engine idling or just stopped, per your manual.

On the road: every 500 km

3 items
  • Check lights, horn, brake light switches
    Pre-ride / on the road
    Guideline
  • Check tire pressures
    Pre-ride / on the road
    Guideline
  • Lubricate drive chain
    Pre-ride / on the road
    Guideline

    Lube warm, ideally at the end of the riding day so it soaks in overnight. Sooner after rain.

On the road: every 800 km

1 item
  • Check coolant level
    Pre-ride / on the road
    Guideline

On the road: every 1,000 km

1 item
  • Check chain slack and rear wheel alignment
    Pre-ride / on the road
    Guideline

Every 1,600 km or 6 months

1 item
  • Inspect tire tread, sidewalls and date codes
    Wheels and tires
    Guideline

Every 5,000 km or 12 months

10 items
  • Check throttle cable(s) free play and return
    Fuel and air
    Guideline
  • Clean drive chain thoroughly (remove and soak, re-lube)
    Final drive
    Guideline

    Non O-ring chains on old machines: remove, clean, soak in hot chain grease or lube, refit with the master link clip closed end leading.

  • Inspect chain and sprockets for wear (measure stretch)
    Final drive
    Guideline
  • Check steering head bearing adjustment
    Front end
    Guideline
  • Inspect fork seals, stanchions and fork boots
    Front end
    Guideline
  • Check footrests, pegs, rear brake and gear lever pivots
    Rear suspension and frame
    Guideline
  • Grease and check center / side stand and springs
    Rear suspension and frame
    Guideline
  • Check brake pads and discs
    Brakes
    Guideline
  • Check spoke tension and wheel true
    Wheels and tires
    Guideline
  • Check wheel bearings for play
    Wheels and tires
    Guideline

Every 6,500 km or 12 months

1 item
  • Inspect, clean and gap spark plugs
    Engine
    Guideline

Every 8,000 km or 12 months

2 items
  • Change engine oil
    Engine
    Guideline

    Pre-1970 machines: many owners run non-detergent or classic-spec oil with no filter, so short intervals matter. Dry sump: drain the tank and the crankcase/sump, flush the tank and clean the feed and return screens.

  • Replace oil filter
    Engine
    Guideline

Every 9,500 km or 12 months

7 items
  • Inspect coolant hoses and clamps
    Engine
    Guideline
  • Clean / inspect air filter
    Fuel and air
    Guideline

    Mesh or oiled foam: clean and re-oil. Paper: blow out or replace. Some very early machines have no filter at all.

  • Check charging voltage and regulator / cut-out
    Ignition and electrics
    Guideline
  • Check swingarm bushes for play
    Rear suspension and frame
    Guideline
  • Inspect rear shocks for leaks and damping
    Rear suspension and frame
    Guideline
  • Lubricate control cables and lever pivots
    Controls and cables
    Guideline
  • Lubricate speedometer / tachometer cables, check drive
    Controls and cables
    Guideline

    A dry speedo cable whips the needle and eventually kills the instrument.

Every 16,000 km or 2 years

1 item
  • Compression test (or leak-down)
    Engine
    Guideline

Every 19,500 km or 2 years

4 items
  • Replace air filter element
    Fuel and air
    Guideline
  • Synchronize throttle bodies
    Fuel and air
    Guideline
  • Clean and grease rear suspension linkage
    Rear suspension and frame
    Guideline
  • Grease swingarm pivot
    Rear suspension and frame
    Guideline

Every 24,000 km or 3 years

1 item
  • Change fork oil
    Front end
    Guideline

    Some early telescopic forks are grease filled or use very small oil quantities. Check your manual.

Every 24,000 km or 4 years

1 item
  • Check valve clearances (shim adjusted)
    Engine
    Guideline

Every 25,500 km or 4 years

1 item
  • Replace spark plugs
    Engine
    Guideline

Every 29,000 km

1 item
  • Replace chain and sprockets (wear based)
    Final drive
    Guideline

Every 32,000 km or 4 years

2 items
  • Repack / replace steering head bearings
    Front end
    Guideline

    Many old machines use loose balls in cups and cones. Taper roller conversions are common.

  • Repack / replace wheel bearings
    Wheels and tires
    Guideline

    Cup-and-cone and taper roller hubs need periodic repacking and adjustment.

Every 38,500 km or 4 years

1 item
  • Replace fuel filter
    Fuel and air
    Guideline

Every 40,000 km or 6 years

1 item
  • Replace swingarm bushes / bearings
    Rear suspension and frame
    Guideline

Every 48,500 km or 6 years

1 item
  • Rebuild forks: seals, bushes, springs
    Front end
    Guideline

Every 10 h

36 items
  • All moving parts (grease, check smooth operation)
    Engine
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Antifreeze and coolant level (check)
    Engine
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): after 1 operating hour, then every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Engine oil and oil filter (change; clean oil screen)
    Engine
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): after 1 operating hour, then every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Fault memory (read out with diagnostics tool)
    Engine
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): after 1 operating hour, then every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Final check and test ride; read fault memory after the ride
    Engine
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): after 1 operating hour, then every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Hoses and sleeves (check for cracking, tightness and routing)
    Engine
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): after 1 operating hour, then every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Idle speed (check)
    Engine
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): after 1 operating hour, then every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Rim run-out (check)
    Engine
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): after 1 operating hour, then every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Safety-relevant screws and nuts (check tightness)
    Engine
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): after 1 operating hour, then every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Air filter and air filter box (clean)
    Fuel and air
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Fuel pressure (check)
    Fuel and air
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Fuel screen (change)
    Fuel and air
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): after 1 operating hour, then every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • 12 V battery (check, charge)
    Ignition and electrics
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Hydraulic clutch fluid level (check, correct)
    Primary and gearbox
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Chain tension (check)
    Final drive
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): after 1 operating hour, then every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Chain, rear sprocket, engine sprocket and chain guide (check)
    Final drive
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Link fork (check)
    Front end
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Steering head bearing (check for play)
    Front end
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): after 1 operating hour, then every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Frame (check)
    Rear suspension and frame
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Shock absorber heim joint (check for play)
    Rear suspension and frame
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Shock absorber linkage (check)
    Rear suspension and frame
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Brake discs (check)
    Brakes
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Brake lines (check for damage and leakage)
    Brakes
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Foot brake lever free travel (check)
    Brakes
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Front brake fluid level (check)
    Brakes
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Front brake linings (check)
    Brakes
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Hand brake lever free travel (check)
    Brakes
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Rear brake fluid level (check)
    Brakes
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Rear brake linings (check)
    Brakes
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Spoke tension (check)
    Wheels and tires
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): after 1 operating hour, then every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Tire condition (check)
    Wheels and tires
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): after 1 operating hour, then every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Tire pressure (check)
    Wheels and tires
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): after 1 operating hour, then every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Wheel bearings (check for play)
    Wheels and tires
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Wheel hubs (check)
    Wheels and tires
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Cables (check for damage and kink-free routing)
    Controls and cables
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Throttle cables (check condition, routing and setting)
    Controls and cables
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): after 1 operating hour, then every 10 operating hours and after every race. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

Every 20 h

3 items
  • Main muffler glass fiber yarn filling (change)
    Engine
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 20 operating hours. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Clutch (check)
    Primary and gearbox
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 20 operating hours. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Fork bearing (check for play)
    Front end
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 20 operating hours. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

Every 30 h

2 items
  • Valve clearance (check)
    Engine
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): after 1 operating hour, then every 30 operating hours. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Water pump cover seal and radial shaft seal rings (change)
    Engine
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 30 operating hours. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

Every 40 h

2 items
  • Fork (service)
    Front end
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 40 operating hours (required); recommended once after 10 operating hours. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Shock absorber (service)
    Rear suspension and frame
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 40 operating hours (required); recommended once after 20 operating hours. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

Every 50 h

1 item
  • Minor engine service (recommended): spark plug and connector, piston, cylinder, cylinder head, camshaft and cam lever, timing assembly, intake flange
    Controls and cables
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 50 operating hours (marked in the 50 and 100 hour columns). Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

Every 100 h

2 items
  • Fuel filter (change; recommended)
    Fuel and air
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 100 operating hours. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Major engine service (recommended): valves, springs, seats and retainers, connecting rod, conrod bearing and crank pin, transmission and shift mechanism, oil pressure control valve, suction pump, force pump and lubrication system, timing chain, all engine bearings, freewheel
    Final drive
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 100 operating hours. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

Every 6 months

1 item
  • Clean battery terminals, check charge and strap
    Ignition and electrics
    Guideline

Every 12 months

4 items
  • Hydraulic clutch fluid (change; recommended)
    Primary and gearbox
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 12 months (marked in the 12 and 48 month columns). Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Steering head bearing (lubricate; recommended)
    Front end
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 12 months (marked in the 12 and 48 month columns). Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Front brake fluid (change; recommended)
    Brakes
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 12 months (marked in the 12 and 48 month columns). Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Rear brake fluid (change; recommended)
    Brakes
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 12 months (marked in the 12 and 48 month columns). Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

Every 2 years

5 items
  • Replace coolant
    Engine
    Guideline
  • Inspect wiring, bullet connectors and ground points
    Ignition and electrics
    Guideline
  • Replace hydraulic clutch fluid
    Primary and gearbox
    Guideline
  • Inspect frame, welds and lugs for cracks
    Rear suspension and frame
    Guideline
  • Replace brake fluid
    Brakes
    Guideline

Every 4 years

4 items
  • Coolant (change; recommended)
    Engine
    Factory

    Factory: Service schedule (Husqvarna Owner's Manual 2022 FC 350 / FX 350, art. no. 3402534en, section 9, printed pp.35-37): every 48 months. Required work columns as printed: after 1 operating hour (one-time); every 10, 20, 30 and 40 operating hours; after every race. Recommended work columns: after 10 and after 20 operating hours (one-time); every 50 and every 100 operating hours; every 12 months; every 48 months. Different intervals may apply in your country.

  • Replace fuel lines
    Fuel and air
    Guideline

    Old rubber and modern ethanol fuel do not mix well.

  • Inspect brake hoses; replace old rubber
    Brakes
    Guideline
  • Rebuild calipers and master cylinders (seals)
    Brakes
    Guideline

Every 6 years

2 items
  • Replace inner tubes and rim tape with tires
    Wheels and tires
    Guideline
  • Replace tires on age (regardless of tread)
    Wheels and tires
    Guideline

Guideline lines: Intervals here are general guidelines for the machine's era and layout, compiled for this app. They are not factory manual figures. Check your workshop manual, and edit any interval in the bike's Schedule tab.

Keep up with this schedule on your phone

Add the bike in the app and this chart loads itself, ready to log against and edit.

Coming soon to Google Play

Other 2019 Husqvarna models

All 2019 Husqvarna
2002-2025
TC 250
Factory
2002-2025
TE 250
Factory
2014-2024
701 Enduro
Guideline
2014-2025
FC 250
Factory
2014-2025
FC 350
Factory
2014-2025
FC 450
Factory
2014-2025
FE 250
Guideline
2014-2025
FE 350
Factory