No photo of this model in the library yet.

Have this bike? Send a photo or the manual's service chart

Husqvarna · Shim-adjusted overhead-cam four-stroke, wet sump, gearbox shares engine oil, chain drive

FX 450

Library entry covers 2017-2024

52 factory 52 guideline

Published source

Husqvarna 2022 FC 450 / FX 450 owner's manual (art. no. 3402535en), service schedule 9.2-9.3 pp.35-37 (ManualsLib viewer pp.37-39)

Factory owner's handbook. Covers Husqvarna 2022 owner's manual for the FC 450 and FX 450 (model year 2022 only).

104 items for a 2017 model, grouped by interval the way a factory chart is laid out.

How this bike is built (what the schedule is based on)

Engine cycle: Four-stroke
Engine lubrication: Wet sump (oil in crankcase)
Oil filtration: Replaceable cartridge or spin-on filter
Valve gear: Overhead cam, shim adjusted (incl. desmo)
Ignition: Electronic (CDI / transistor / ECU)
Charging: Alternator / stator with rectifier
Battery: Wet cell (flooded lead-acid, needs topping up)
Fuel system: Fuel injection
Cooling: Liquid cooled
Primary drive: Gear or chain inside engine, shares engine oil
Gearbox oil: Shares engine oil
Clutch control: Hand lever, hydraulic
Final drive: Chain
Front suspension: Telescopic fork
Rear suspension: Swingarm, single shock / cantilever
Front brake: Disc, hydraulic
Rear brake: Disc, hydraulic
Wheels: Spoked, tubed
Sidecar: No sidecar

Maintenance schedule

2017 Husqvarna FX 450

On the road: every 300 km

1 item

Check engine oil level

Pre-ride / on the road

Guideline

Each fuel stop on old machines. Dry sump: check the tank hot, engine idling or just stopped, per your manual.

On the road: every 500 km

3 items

Check lights, horn, brake light switches

Pre-ride / on the road

Guideline
Check tire pressures

Pre-ride / on the road

Guideline
Lubricate drive chain

Pre-ride / on the road

Guideline

Lube warm, ideally at the end of the riding day so it soaks in overnight. Sooner after rain.

On the road: every 800 km

1 item

Check coolant level

Pre-ride / on the road

Guideline

On the road: every 1,000 km

1 item

Check chain slack and rear wheel alignment

Pre-ride / on the road

Guideline

Every 1,600 km or 6 months

1 item

Inspect tire tread, sidewalls and date codes

Wheels and tires

Guideline

Every 5,000 km or 12 months

10 items

Check throttle cable(s) free play and return

Fuel and air

Guideline
Clean drive chain thoroughly (remove and soak, re-lube)

Final drive

Guideline

Non O-ring chains on old machines: remove, clean, soak in hot chain grease or lube, refit with the master link clip closed end leading.
Inspect chain and sprockets for wear (measure stretch)

Final drive

Guideline
Check steering head bearing adjustment

Front end

Guideline
Inspect fork seals, stanchions and fork boots

Front end

Guideline
Check footrests, pegs, rear brake and gear lever pivots

Rear suspension and frame

Guideline
Grease and check center / side stand and springs

Rear suspension and frame

Guideline
Check brake pads and discs

Brakes

Guideline
Check spoke tension and wheel true

Wheels and tires

Guideline
Check wheel bearings for play

Wheels and tires

Guideline

Every 6,500 km or 12 months

1 item

Inspect, clean and gap spark plugs

Engine

Guideline

Every 8,000 km or 12 months

2 items

Change engine oil

Engine

Guideline

Pre-1970 machines: many owners run non-detergent or classic-spec oil with no filter, so short intervals matter. Dry sump: drain the tank and the crankcase/sump, flush the tank and clean the feed and return screens.
Replace oil filter

Engine

Guideline

Every 9,500 km or 12 months

7 items

Inspect coolant hoses and clamps

Engine

Guideline
Clean / inspect air filter

Fuel and air

Guideline

Mesh or oiled foam: clean and re-oil. Paper: blow out or replace. Some very early machines have no filter at all.
Check charging voltage and regulator / cut-out

Ignition and electrics

Guideline
Check swingarm bushes for play

Rear suspension and frame

Guideline
Inspect rear shocks for leaks and damping

Rear suspension and frame

Guideline
Lubricate control cables and lever pivots

Controls and cables

Guideline
Lubricate speedometer / tachometer cables, check drive

Controls and cables

Guideline

A dry speedo cable whips the needle and eventually kills the instrument.

Every 16,000 km or 2 years

1 item

Compression test (or leak-down)

Engine

Guideline

Every 19,500 km or 2 years

4 items

Replace air filter element

Fuel and air

Guideline
Synchronize throttle bodies

Fuel and air

Guideline
Clean and grease rear suspension linkage

Rear suspension and frame

Guideline
Grease swingarm pivot

Rear suspension and frame

Guideline

Every 24,000 km or 3 years

1 item

Change fork oil

Front end

Guideline

Some early telescopic forks are grease filled or use very small oil quantities. Check your manual.

Every 24,000 km or 4 years

1 item

Check valve clearances (shim adjusted)

Engine

Guideline

Every 25,500 km or 4 years

1 item

Replace spark plugs

Engine

Guideline

Every 29,000 km

1 item

Replace chain and sprockets (wear based)

Final drive

Guideline

Every 32,000 km or 4 years

2 items

Repack / replace steering head bearings

Front end

Guideline

Many old machines use loose balls in cups and cones. Taper roller conversions are common.
Repack / replace wheel bearings

Wheels and tires

Guideline

Cup-and-cone and taper roller hubs need periodic repacking and adjustment.

Every 38,500 km or 4 years

1 item

Replace fuel filter

Fuel and air

Guideline

Every 40,000 km or 6 years

1 item

Replace swingarm bushes / bearings

Rear suspension and frame

Guideline

Every 48,500 km or 6 years

1 item

Rebuild forks: seals, bushes, springs

Front end

Guideline

Every 10 h

38 items

All moving parts (grease, check smooth operation)

Engine

Factory

Factory: Required work 9.2 (p.35): every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Antifreeze and coolant level (check)

Engine

Factory

Factory: Required work 9.2 (p.36): once after 1 hour, then every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Engine oil and oil filter (change), oil screens (clean)

Engine

Factory

Factory: Required work 9.2 (p.35): once after 1 hour, then every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Fault memory (read with diagnostics tool)

Engine

Factory

Factory: Required work 9.2 (p.35): once after 1 hour, then every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Final check and test ride

Engine

Factory

Factory: Required work 9.2 (p.36): once after 1 hour, then every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Idle speed (check)

Engine

Factory

Factory: Required work 9.2 (p.36): once after 1 hour, then every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Rim runout (check)

Engine

Factory

Factory: Required work 9.2 (p.35): once after 1 hour, then every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Safety-relevant screws and nuts (check tightness)

Engine

Factory

Factory: Required work 9.2 (p.36): once after 1 hour, then every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Air filter and air filter box (clean)

Fuel and air

Factory

Factory: Required work 9.2 (p.36): every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Fuel pressure (check)

Fuel and air

Factory

Factory: Required work 9.2 (p.36): every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Fuel screen (change)

Fuel and air

Factory

Factory: Required work 9.2 (p.36): once after 1 hour, then every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Hoses and sleeves: fuel, cooling, bleeder, drain (check)

Fuel and air

Factory

Factory: Required work 9.2 (p.36): once after 1 hour, then every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
12 V battery (check, charge)

Ignition and electrics

Factory

Factory: Required work 9.2 (p.35): every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Clutch (check)

Primary and gearbox

Factory

Factory: Required work 9.2 (p.35): every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Hydraulic clutch fluid level (check, correct)

Primary and gearbox

Factory

Factory: Required work 9.2 (p.35): every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Chain tension (check)

Final drive

Factory

Factory: Required work 9.2 (p.35): once after 1 hour, then every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Chain, rear sprocket, engine sprocket and chain guide (check)

Final drive

Factory

Factory: Required work 9.2 (p.35): every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Fork (service), recommended

Front end

Factory

Factory: Recommended work 9.3 (p.36): once after 10 hours. Recommended work columns: after 10 operating hours; after 20 operating hours; every 50 and 100 operating hours; every 12 months; every 48 months.
Steering head bearing play (check)

Front end

Factory

Factory: Required work 9.2 (p.35): once after 1 hour, then every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Swingarm (link fork) (check)

Front end

Factory

Factory: Required work 9.2 (p.35): every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Frame (check)

Rear suspension and frame

Factory

Factory: Required work 9.2 (p.35): every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Shock absorber heim joint play (check)

Rear suspension and frame

Factory

Factory: Required work 9.2 (p.35): every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Shock absorber linkage (check)

Rear suspension and frame

Factory

Factory: Required work 9.2 (p.35): every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Brake discs (check)

Brakes

Factory

Factory: Required work 9.2 (p.35): every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Brake lines (check damage and leaks)

Brakes

Factory

Factory: Required work 9.2 (p.35): every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Foot brake lever free travel (check)

Brakes

Factory

Factory: Required work 9.2 (p.35): every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Front brake fluid level (check)

Brakes

Factory

Factory: Required work 9.2 (p.35): every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Front brake linings (check)

Brakes

Factory

Factory: Required work 9.2 (p.35): every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Hand brake lever free travel (check)

Brakes

Factory

Factory: Required work 9.2 (p.35): every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Rear brake fluid level (check)

Brakes

Factory

Factory: Required work 9.2 (p.35): every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Rear brake linings (check)

Brakes

Factory

Factory: Required work 9.2 (p.35): every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Spoke tension (check)

Wheels and tires

Factory

Factory: Required work 9.2 (p.35): once after 1 hour, then every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Tire condition (check)

Wheels and tires

Factory

Factory: Required work 9.2 (p.35): once after 1 hour, then every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Tire pressure (check)

Wheels and tires

Factory

Factory: Required work 9.2 (p.35): once after 1 hour, then every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Wheel bearing play (check)

Wheels and tires

Factory

Factory: Required work 9.2 (p.35): every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Wheel hubs (check)

Wheels and tires

Factory

Factory: Required work 9.2 (p.35): every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Cables (check damage and routing)

Controls and cables

Factory

Factory: Required work 9.2 (p.36): every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Throttle cables (check condition, routing, adjustment)

Controls and cables

Factory

Factory: Required work 9.2 (p.36): once after 1 hour, then every 10 hours and after every race. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.

Every 20 h

3 items

Main muffler glass fiber packing (change)

Engine

Factory

Factory: Required work 9.2 (p.36): every 20 hours. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Shock absorber (service), recommended

Rear suspension and frame

Factory

Factory: Recommended work 9.3 (p.36): once after 20 hours. Recommended work columns: after 10 operating hours; after 20 operating hours; every 50 and 100 operating hours; every 12 months; every 48 months.
Swingarm bearing play (check)

Rear suspension and frame

Factory

Factory: Required work 9.2 (p.35): every 20 hours. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.

Every 30 h

1 item

Valve clearance (check)

Engine

Factory

Factory: Required work 9.2 (p.35): once after 1 hour, then every 30 hours. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.

Every 40 h

2 items

Fork (service)

Front end

Factory

Factory: Required work 9.2 (p.36): every 40 hours. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.
Shock absorber (service)

Rear suspension and frame

Factory

Factory: Required work 9.2 (p.36): every 40 hours. Required work columns: after 1 operating hour; every 10, 20, 30 and 40 operating hours; after every race. Open circle = one-time interval; filled dot = periodic interval. Local intervals may differ; the current schedule is on Husqvarna Motorcycles Dealer.net.

Every 50 h

1 item

Minor engine service (spark plug and connector, piston, cylinder, head, camshaft, rocker arms, timing assembly)

Ignition and electrics

Factory

Factory: Recommended work 9.3 (p.36): every 50 hours. Recommended work columns: after 10 operating hours; after 20 operating hours; every 50 and 100 operating hours; every 12 months; every 48 months.

Every 100 h

2 items

Fuel filter (change)

Fuel and air

Factory

Factory: Recommended work 9.3 (p.36): every 100 hours. Recommended work columns: after 10 operating hours; after 20 operating hours; every 50 and 100 operating hours; every 12 months; every 48 months.
Major engine service (valves and springs, conrod and crank pin, transmission, oil pumps, timing chain, all engine bearings, main bearing seals)

Final drive

Factory

Factory: Recommended work 9.3 (p.37): every 100 hours. Recommended work columns: after 10 operating hours; after 20 operating hours; every 50 and 100 operating hours; every 12 months; every 48 months.

Every 6 months

1 item

Clean battery terminals, check charge and strap

Ignition and electrics

Guideline

Every 12 months

4 items

Hydraulic clutch fluid (change)

Primary and gearbox

Factory

Factory: Recommended work 9.3 (p.36): every 12 months. Recommended work columns: after 10 operating hours; after 20 operating hours; every 50 and 100 operating hours; every 12 months; every 48 months.
Steering head bearing (lubricate)

Front end

Factory

Factory: Recommended work 9.3 (p.36): every 12 months. Recommended work columns: after 10 operating hours; after 20 operating hours; every 50 and 100 operating hours; every 12 months; every 48 months.
Front brake fluid (change)

Brakes

Factory

Factory: Recommended work 9.3 (p.36): every 12 months. Recommended work columns: after 10 operating hours; after 20 operating hours; every 50 and 100 operating hours; every 12 months; every 48 months.
Rear brake fluid (change)

Brakes

Factory

Factory: Recommended work 9.3 (p.36): every 12 months. Recommended work columns: after 10 operating hours; after 20 operating hours; every 50 and 100 operating hours; every 12 months; every 48 months.

Every 2 years

5 items

Replace coolant

Engine

Guideline
Inspect wiring, bullet connectors and ground points

Ignition and electrics

Guideline
Replace hydraulic clutch fluid

Primary and gearbox

Guideline
Inspect frame, welds and lugs for cracks

Rear suspension and frame

Guideline
Replace brake fluid

Brakes

Guideline

Every 4 years

4 items

Coolant (change)

Engine

Factory

Factory: Recommended work 9.3 (p.36): every 48 months. Recommended work columns: after 10 operating hours; after 20 operating hours; every 50 and 100 operating hours; every 12 months; every 48 months.
Replace fuel lines

Fuel and air

Guideline

Old rubber and modern ethanol fuel do not mix well.
Inspect brake hoses; replace old rubber

Brakes

Guideline
Rebuild calipers and master cylinders (seals)

Brakes

Guideline

Every 6 years

2 items

Replace inner tubes and rim tape with tires

Wheels and tires

Guideline
Replace tires on age (regardless of tread)

Wheels and tires

Guideline

Guideline lines: Intervals here are general guidelines for the machine's era and layout, compiled for this app. They are not factory manual figures. Check your workshop manual, and edit any interval in the bike's Schedule tab.