MotoService Log
No photo of this model in the library yet.

Have this bike? Send a photo or the manual's service chart

Husqvarna · Shim-adjusted overhead-cam four-stroke, wet sump, gearbox shares engine oil, chain drive

SMR 511

Library entry covers 2011-2014

65 factory 50 guideline

Published source

Husqvarna SMR 511 2012 I.E. owner's manual (Ed.00 12/2011), scheduled maintenance chart pp.252-261 (ManualsLib.mx 214905)

Factory source. Covers 2012 model (cover prints SMR 511 2012 I.E., Ed.00 12/2011); catalog row spans 2011-2014, other model years may differ.

115 items for a 2014 model, grouped by interval the way a factory chart is laid out.

How this bike is built (what the schedule is based on)
Engine cycle
Four-stroke
Engine lubrication
Wet sump (oil in crankcase)
Oil filtration
Replaceable cartridge or spin-on filter
Valve gear
Overhead cam, shim adjusted (incl. desmo)
Ignition
Electronic (CDI / transistor / ECU)
Charging
Alternator / stator with rectifier
Battery
Wet cell (flooded lead-acid, needs topping up)
Fuel system
Fuel injection
Cooling
Liquid cooled
Primary drive
Gear or chain inside engine, shares engine oil
Gearbox oil
Shares engine oil
Clutch control
Hand lever, hydraulic
Final drive
Chain
Front suspension
Telescopic fork
Rear suspension
Swingarm, single shock / cantilever
Front brake
Disc, hydraulic
Rear brake
Disc, hydraulic
Wheels
Cast / alloy, tubeless
Sidecar
No sidecar
Maintenance schedule

2014 Husqvarna SMR 511

On the road: every 300 km

1 item
  • Check engine oil level
    Pre-ride / on the road
    Guideline

    Each fuel stop on old machines. Dry sump: check the tank hot, engine idling or just stopped, per your manual.

On the road: every 500 km

3 items
  • Check lights, horn, brake light switches
    Pre-ride / on the road
    Guideline
  • Check tire pressures
    Pre-ride / on the road
    Guideline
  • Lubricate drive chain
    Pre-ride / on the road
    Guideline

    Lube warm, ideally at the end of the riding day so it soaks in overnight. Sooner after rain.

On the road: every 800 km

1 item
  • Check coolant level
    Pre-ride / on the road
    Guideline

On the road: every 1,000 km

1 item
  • Check chain slack and rear wheel alignment
    Pre-ride / on the road
    Guideline

Every 1,000 km

19 items
  • Coolant (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C every 1,000 km; X replace if necessary.

  • Coolant hoses (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C every 1,000 km.

  • Engine oil (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C every 1,000 km.

  • Exhaust pipe and muffler (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. p.261: C every 1,000 km; X replace if necessary.

  • Footrests (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C every 1,000 km; X replace if necessary.

  • Radiators (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C every 1,000 km.

  • Air filter (clean and lubricate)
    Fuel and air
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. P/L every 1,000 km and after the first 1,000 km.

  • Clutch control assembly (check)
    Primary and gearbox
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. p.260: C every 1,000 km.

  • Chain guide (check)
    Final drive
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C every 1,000 km; X replace if necessary.

  • Chain guide roller (check)
    Final drive
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C every 1,000 km.

  • Chain slider (check)
    Final drive
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C every 1,000 km; X replace if necessary.

  • Drive chain (lubricate)
    Final drive
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. L every 1,000 km; C/L after the first 1,000 km; C every 5,000 km; X replace if necessary.

  • Rear suspension linkage and shock bearings (lubricate)
    Rear suspension and frame
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. p.260: L(*) every 1,000 km and after every pressure wash.

  • Side stand (check)
    Rear suspension and frame
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C every 1,000 km.

  • Swingarm pivot bearings (lubricate)
    Rear suspension and frame
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. L(*) every 1,000 km and after every pressure wash.

  • Brake pads (check)
    Brakes
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. p.260: C every 1,000 km; X replace if necessary.

  • Front brake fluid (check)
    Brakes
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. p.260: C every 1,000 km.

  • Rear brake fluid (check)
    Brakes
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. p.260: C every 1,000 km.

  • Throttle control assembly (check and lubricate)
    Controls and cables
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. p.260: C/L every 1,000 km.

Every 1,600 km or 6 months

1 item
  • Inspect tire tread, sidewalls and date codes
    Wheels and tires
    Guideline

Every 5,000 km or 12 months

9 items
  • Check throttle cable(s) free play and return
    Fuel and air
    Guideline
  • Clean drive chain thoroughly (remove and soak, re-lube)
    Final drive
    Guideline

    Non O-ring chains on old machines: remove, clean, soak in hot chain grease or lube, refit with the master link clip closed end leading.

  • Inspect chain and sprockets for wear (measure stretch)
    Final drive
    Guideline
  • Check steering head bearing adjustment
    Front end
    Guideline
  • Inspect fork seals, stanchions and fork boots
    Front end
    Guideline
  • Check footrests, pegs, rear brake and gear lever pivots
    Rear suspension and frame
    Guideline
  • Grease and check center / side stand and springs
    Rear suspension and frame
    Guideline
  • Check brake pads and discs
    Brakes
    Guideline
  • Check wheel bearings for play
    Wheels and tires
    Guideline

Every 5,000 km

14 items
  • Engine oil (change)
    Engine
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. S after the first 1,000 km and every 5,000 km.

  • Engine oil filters (change)
    Engine
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. S after the first 1,000 km and every 5,000 km.

  • Handlebar holders (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C after the first 1,000 km and every 5,000 km.

  • Intake coupling (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C every 5,000 km; X replace if necessary.

  • Lights and horn (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C after the first 1,000 km and every 5,000 km.

  • Sprockets (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C after the first 1,000 km and every 5,000 km. X replace if necessary.

  • Valve clearance (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C(*) after the first 1,000 km and every 5,000 km.

  • Battery (check)
    Ignition and electrics
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C every 5,000 km.

  • Clutch plates (check)
    Primary and gearbox
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C every 5,000 km; X replace if necessary.

  • Steering head bearings (lubricate)
    Front end
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. L every 5,000 km.

  • Subframe and engine mounting screws (check)
    Rear suspension and frame
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C after the first 1,000 km and every 5,000 km.

  • Front brake disc (check)
    Brakes
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. p.260: C every 5,000 km; X replace if necessary.

  • Rear brake disc (check)
    Brakes
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. p.260: C every 5,000 km; X replace if necessary.

  • Wheel spokes (check)
    Wheels and tires
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C after the first 1,000 km and every 5,000 km.

Every 6,500 km or 12 months

1 item
  • Inspect, clean and gap spark plugs
    Engine
    Guideline

Every 8,000 km or 12 months

2 items
  • Change engine oil
    Engine
    Guideline

    Pre-1970 machines: many owners run non-detergent or classic-spec oil with no filter, so short intervals matter. Dry sump: drain the tank and the crankcase/sump, flush the tank and clean the feed and return screens.

  • Replace oil filter
    Engine
    Guideline

Every 9,500 km or 12 months

7 items
  • Inspect coolant hoses and clamps
    Engine
    Guideline
  • Clean / inspect air filter
    Fuel and air
    Guideline

    Mesh or oiled foam: clean and re-oil. Paper: blow out or replace. Some very early machines have no filter at all.

  • Check charging voltage and regulator / cut-out
    Ignition and electrics
    Guideline
  • Check swingarm bushes for play
    Rear suspension and frame
    Guideline
  • Inspect rear shocks for leaks and damping
    Rear suspension and frame
    Guideline
  • Lubricate control cables and lever pivots
    Controls and cables
    Guideline
  • Lubricate speedometer / tachometer cables, check drive
    Controls and cables
    Guideline

    A dry speedo cable whips the needle and eventually kills the instrument.

Every 10,000 km

32 items
  • Buckets and rocker arm (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C every 10,000 km; X replace if necessary.

  • Camshaft (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C every 10,000 km.

  • Crankcase bearings (change)
    Engine
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. S every 10,000 km.

  • Crankshaft (change)
    Engine
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. S every 10,000 km.

  • Cylinder (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C every 10,000 km; X replace if necessary.

  • Cylinder head (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C every 10,000 km.

  • Gear shift pedal (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C every 10,000 km; X replace if necessary.

  • Head gasket (change)
    Engine
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. S every 10,000 km.

  • Oil pump (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C every 10,000 km.

  • Overall tightening of nuts and bolts (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. p.260: C after the first 1,000 km and every 10,000 km.

  • Piston (change)
    Engine
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. S every 10,000 km.

  • Spark plug (change)
    Engine
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. S every 10,000 km.

  • Starter gears (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C every 10,000 km; X replace if necessary.

  • Valve retainers and collets (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C every 10,000 km; X replace if necessary.

  • Valve springs (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C every 10,000 km; X replace if necessary.

  • Valves (change)
    Engine
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. S every 10,000 km.

  • Fuel hoses (check)
    Fuel and air
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. p.261: C every 10,000 km; X replace if necessary.

  • Timing driven and drive gears (check)
    Ignition and electrics
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C every 10,000 km; X replace if necessary.

  • Clutch hub and housing (check)
    Primary and gearbox
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C every 10,000 km; X replace if necessary.

  • Clutch pressure plate (check)
    Primary and gearbox
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C every 10,000 km.

  • Clutch pushrod (check)
    Primary and gearbox
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C every 10,000 km; X replace if necessary.

  • Gearbox (check)
    Primary and gearbox
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C every 10,000 km; X replace if necessary.

  • Primary drive torque limiter (check)
    Primary and gearbox
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C every 10,000 km; X replace if necessary.

  • Timing chain (change)
    Final drive
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. S every 10,000 km.

  • Timing chain slider (check)
    Final drive
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C every 10,000 km; X replace if necessary.

  • Timing chain tensioner (check)
    Final drive
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. C every 10,000 km; X replace if necessary.

  • Front fork (overhaul)
    Front end
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. R every 10,000 km.

  • Rear shock absorber (check)
    Rear suspension and frame
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. p.260: C every 10,000 km; X replace if necessary.

  • Brake pump and caliper hoses (check)
    Brakes
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. p.261: C every 10,000 km; X replace if necessary.

  • Front brake fluid (change)
    Brakes
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. p.260: S every 10,000 km.

  • Rear brake fluid (change)
    Brakes
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. p.260: S every 10,000 km.

  • Wheel hub bearings (check)
    Wheels and tires
    Factory

    Factory: Scheduled maintenance chart (owner's manual SMR 511 2012 I.E., Ed.00 12/2011, IT/EN/FR table, engine pp.252-254, chassis pp.258-261; to be carried out at the Husqvarna dealer; columns every 1,000 km, after the first 1,000 km, every 5,000 km, every 10,000 km, replace if necessary). Codes: C = check, C(*) = check clearance, L = lubricate, L(*) = lubricate after every pressure wash, P = clean, S = change, R = front fork overhaul, X = replace if necessary. p.261: C every 10,000 km; X replace if necessary.

Every 16,000 km or 2 years

1 item
  • Compression test (or leak-down)
    Engine
    Guideline

Every 19,500 km or 2 years

4 items
  • Replace air filter element
    Fuel and air
    Guideline
  • Synchronize throttle bodies
    Fuel and air
    Guideline
  • Clean and grease rear suspension linkage
    Rear suspension and frame
    Guideline
  • Grease swingarm pivot
    Rear suspension and frame
    Guideline

Every 24,000 km or 3 years

1 item
  • Change fork oil
    Front end
    Guideline

    Some early telescopic forks are grease filled or use very small oil quantities. Check your manual.

Every 24,000 km or 4 years

1 item
  • Check valve clearances (shim adjusted)
    Engine
    Guideline

Every 25,500 km or 4 years

1 item
  • Replace spark plugs
    Engine
    Guideline

Every 29,000 km

1 item
  • Replace chain and sprockets (wear based)
    Final drive
    Guideline

Every 32,000 km or 4 years

2 items
  • Repack / replace steering head bearings
    Front end
    Guideline

    Many old machines use loose balls in cups and cones. Taper roller conversions are common.

  • Repack / replace wheel bearings
    Wheels and tires
    Guideline

    Cup-and-cone and taper roller hubs need periodic repacking and adjustment.

Every 38,500 km or 4 years

1 item
  • Replace fuel filter
    Fuel and air
    Guideline

Every 40,000 km or 6 years

1 item
  • Replace swingarm bushes / bearings
    Rear suspension and frame
    Guideline

Every 48,500 km or 6 years

1 item
  • Rebuild forks: seals, bushes, springs
    Front end
    Guideline

Every 6 months

1 item
  • Clean battery terminals, check charge and strap
    Ignition and electrics
    Guideline

Every 2 years

5 items
  • Replace coolant
    Engine
    Guideline
  • Inspect wiring, bullet connectors and ground points
    Ignition and electrics
    Guideline
  • Replace hydraulic clutch fluid
    Primary and gearbox
    Guideline
  • Inspect frame, welds and lugs for cracks
    Rear suspension and frame
    Guideline
  • Replace brake fluid
    Brakes
    Guideline

Every 4 years

3 items
  • Replace fuel lines
    Fuel and air
    Guideline

    Old rubber and modern ethanol fuel do not mix well.

  • Inspect brake hoses; replace old rubber
    Brakes
    Guideline
  • Rebuild calipers and master cylinders (seals)
    Brakes
    Guideline

Every 6 years

1 item
  • Replace tires on age (regardless of tread)
    Wheels and tires
    Guideline

Guideline lines: Intervals here are general guidelines for the machine's era and layout, compiled for this app. They are not factory manual figures. Check your workshop manual, and edit any interval in the bike's Schedule tab.

Keep up with this schedule on your phone

Add the bike in the app and this chart loads itself, ready to log against and edit.

Coming soon to Google Play

Other 2014 Husqvarna models

All 2014 Husqvarna
2002-2025
TC 250
Factory
2002-2025
TE 250
Factory
2011-2014
SMR 449
Guideline
2012-2014
Nuda (898 cc)
Guideline
2013-2014
TR 650 Strada
Guideline
2013-2014
TR 650 Terra
Guideline
2014-2024
701 Enduro
Guideline
2014-2025
FC 250
Factory