No photo of this model in the library yet.

Have this bike? Send a photo or the manual's service chart

Husqvarna · Two-stroke single, premix, chain drive

TE 150

Library entry covers 2017-2025

59 factory 52 guideline

Published source

Husqvarna Motorcycles Owner's Manual 2023 TE 150 (Art. no. 3402634en), Service schedule printed pp.43-45 (dealer-hosted factory PDF)

Factory owner's handbook. Covers Husqvarna Motorcycles TE 150 owner's manual 2023 (Art. no. 3402634en); other model years not covered.

111 items for a 2023 model, grouped by interval the way a factory chart is laid out.

How this bike is built (what the schedule is based on)

Engine cycle: Two-stroke
Engine lubrication: Two-stroke premix (oil in fuel)
Oil filtration: None (no filter)
Valve gear: None (two-stroke porting)
Ignition: Electronic (CDI / transistor / ECU)
Charging: Alternator / stator with rectifier
Battery: Wet cell (flooded lead-acid, needs topping up)
Fuel system: Single carburetor
Cooling: Liquid cooled
Primary drive: Gear or chain inside engine, shares engine oil
Gearbox oil: Separate gearbox oil
Clutch control: Hand lever, hydraulic
Final drive: Chain
Front suspension: Telescopic fork
Rear suspension: Swingarm, single shock / cantilever
Front brake: Disc, hydraulic
Rear brake: Disc, hydraulic
Wheels: Spoked, tubed
Sidecar: No sidecar

Maintenance schedule

2023 Husqvarna TE 150

On the road: every 200 km

1 item

Check two-stroke oil tank / carry premix oil

Pre-ride / on the road

Guideline

Running a two-stroke out of oil seizes it. Injection bikes: check the tank. Premix: carry oil and a measure.

On the road: every 500 km

3 items

Check lights, horn, brake light switches

Pre-ride / on the road

Guideline
Check tire pressures

Pre-ride / on the road

Guideline
Lubricate drive chain

Pre-ride / on the road

Guideline

Lube warm, ideally at the end of the riding day so it soaks in overnight. Sooner after rain.

On the road: every 800 km

1 item

Check coolant level

Pre-ride / on the road

Guideline

On the road: every 1,000 km

1 item

Check chain slack and rear wheel alignment

Pre-ride / on the road

Guideline

Every 1,600 km or 6 months

1 item

Inspect tire tread, sidewalls and date codes

Wheels and tires

Guideline

Every 3,000 km or 12 months

1 item

Replace spark plugs (two-stroke)

Engine

Guideline

Every 5,000 km or 12 months

11 items

Check throttle cable(s) free play and return

Fuel and air

Guideline
Clean fuel tap filter / sediment bowl

Fuel and air

Guideline
Clean drive chain thoroughly (remove and soak, re-lube)

Final drive

Guideline

Non O-ring chains on old machines: remove, clean, soak in hot chain grease or lube, refit with the master link clip closed end leading.
Inspect chain and sprockets for wear (measure stretch)

Final drive

Guideline
Check steering head bearing adjustment

Front end

Guideline
Inspect fork seals, stanchions and fork boots

Front end

Guideline
Check footrests, pegs, rear brake and gear lever pivots

Rear suspension and frame

Guideline
Grease and check center / side stand and springs

Rear suspension and frame

Guideline
Check brake pads and discs

Brakes

Guideline
Check spoke tension and wheel true

Wheels and tires

Guideline
Check wheel bearings for play

Wheels and tires

Guideline

Every 5,000 km or 2 years

1 item

Decarbonize exhaust ports, pipes and baffles

Engine

Guideline

Two-strokes coke up the exhaust port and muffler baffles; power falls off gradually.

Every 6,500 km or 12 months

1 item

Inspect, clean and gap spark plugs

Engine

Guideline

Every 9,500 km or 12 months

8 items

Inspect coolant hoses and clamps

Engine

Guideline
Clean / inspect air filter

Fuel and air

Guideline

Mesh or oiled foam: clean and re-oil. Paper: blow out or replace. Some very early machines have no filter at all.
Clean carburetor float bowl(s), check float level and jets

Fuel and air

Guideline

Ethanol fuel varnishes old carbs quickly in storage.
Check charging voltage and regulator / cut-out

Ignition and electrics

Guideline
Check swingarm bushes for play

Rear suspension and frame

Guideline
Inspect rear shocks for leaks and damping

Rear suspension and frame

Guideline
Lubricate control cables and lever pivots

Controls and cables

Guideline
Lubricate speedometer / tachometer cables, check drive

Controls and cables

Guideline

A dry speedo cable whips the needle and eventually kills the instrument.

Every 16,000 km or 2 years

2 items

Compression test (or leak-down)

Engine

Guideline
Change gearbox oil

Primary and gearbox

Guideline

Every 19,500 km or 2 years

3 items

Replace air filter element

Fuel and air

Guideline
Clean and grease rear suspension linkage

Rear suspension and frame

Guideline
Grease swingarm pivot

Rear suspension and frame

Guideline

Every 24,000 km or 3 years

1 item

Change fork oil

Front end

Guideline

Some early telescopic forks are grease filled or use very small oil quantities. Check your manual.

Every 25,500 km or 4 years

1 item

Replace spark plugs

Engine

Guideline

Every 29,000 km

1 item

Replace chain and sprockets (wear based)

Final drive

Guideline

Every 32,000 km or 4 years

2 items

Repack / replace steering head bearings

Front end

Guideline

Many old machines use loose balls in cups and cones. Taper roller conversions are common.
Repack / replace wheel bearings

Wheels and tires

Guideline

Cup-and-cone and taper roller hubs need periodic repacking and adjustment.

Every 40,000 km or 6 years

1 item

Replace swingarm bushes / bearings

Rear suspension and frame

Guideline

Every 48,500 km or 6 years

1 item

Rebuild forks: seals, bushes, springs

Front end

Guideline

Every 20 h

39 items

All moving parts (grease, check smooth operation)

Engine

Factory

Factory: Required work (printed pp.43-44): every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Antifreeze and coolant level (check)

Engine

Factory

Factory: Required work (printed pp.43-44): after 1 operating hour (one-time); every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Electrical system function (check)

Engine

Factory

Factory: Required work (printed pp.43-44): after 1 operating hour (one-time); every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Fault memory (read out with diagnostics tool)

Engine

Factory

Factory: Required work (printed pp.43-44): after 1 operating hour (one-time); after 5 operating hours (one-time); every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Final check and test ride

Engine

Factory

Factory: Required work (printed pp.43-44): after 1 operating hour (one-time); after 5 operating hours (one-time); every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Headlight setting (check)

Engine

Factory

Factory: Required work (printed pp.43-44): after 1 operating hour (one-time); every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Hoses and sleeves, cracking, leaks, routing (check)

Engine

Factory

Factory: Required work (printed pp.43-44): after 1 operating hour (one-time); every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Idle speed (check)

Engine

Factory

Factory: Required work (printed pp.43-44): every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Main muffler glass fiber yarn filling (change)

Engine

Factory

Factory: Required work (printed pp.43-44): every 20 operating hours; every 40 operating hours. Key: open circle = one-time interval; solid circle = periodic interval.
Reed valve housing, reed valve and intake flange (check)

Engine

Factory

Factory: Required work (printed pp.43-44): every 20 operating hours; every 40 operating hours. Key: open circle = one-time interval; solid circle = periodic interval.
Rim run-out (check)

Engine

Factory

Factory: Required work (printed pp.43-44): after 1 operating hour (one-time); every 20 operating hours; every 40 operating hours. Key: open circle = one-time interval; solid circle = periodic interval.
Safety-relevant screws and nuts, tightness (check)

Engine

Factory

Factory: Required work (printed pp.43-44): after 1 operating hour (one-time); every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Air filter and air filter box (clean)

Fuel and air

Factory

Factory: Required work (printed pp.43-44): every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Fuel pressure (check)

Fuel and air

Factory

Factory: Required work (printed pp.43-44): every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Fuel screen (change)

Fuel and air

Factory

Factory: Required work (printed pp.43-44): after 1 operating hour (one-time); every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
12-V battery (check, charge)

Ignition and electrics

Factory

Factory: Required work (printed pp.43-44): every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Hydraulic clutch fluid level (check, correct)

Primary and gearbox

Factory

Factory: Required work (printed pp.43-44): every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Chain tension (check)

Final drive

Factory

Factory: Required work (printed pp.43-44): after 1 operating hour (one-time); every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Chain, rear sprocket, engine sprocket and chain guide (check)

Final drive

Factory

Factory: Required work (printed pp.43-44): every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Fork bearing play (check)

Front end

Factory

Factory: Required work (printed pp.43-44): every 20 operating hours; every 40 operating hours. Key: open circle = one-time interval; solid circle = periodic interval.
Link fork (check)

Front end

Factory

Factory: Required work (printed pp.43-44): every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Steering head bearing play (check)

Front end

Factory

Factory: Required work (printed pp.43-44): after 1 operating hour (one-time); every 20 operating hours; every 40 operating hours. Key: open circle = one-time interval; solid circle = periodic interval.
Frame (check)

Rear suspension and frame

Factory

Factory: Required work (printed pp.43-44): every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Shock absorber heim joint play (check)

Rear suspension and frame

Factory

Factory: Required work (printed pp.43-44): every 20 operating hours; every 40 operating hours. Key: open circle = one-time interval; solid circle = periodic interval.
Shock absorber linkage (check)

Rear suspension and frame

Factory

Factory: Required work (printed pp.43-44): every 20 operating hours; every 40 operating hours. Key: open circle = one-time interval; solid circle = periodic interval.
Brake discs (check)

Brakes

Factory

Factory: Required work (printed pp.43-44): every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Brake lines, damage and leakage (check)

Brakes

Factory

Factory: Required work (printed pp.43-44): every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Foot brake lever free travel (check)

Brakes

Factory

Factory: Required work (printed pp.43-44): every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Front brake fluid level (check)

Brakes

Factory

Factory: Required work (printed pp.43-44): every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Front brake linings (check)

Brakes

Factory

Factory: Required work (printed pp.43-44): every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Rear brake fluid level (check)

Brakes

Factory

Factory: Required work (printed pp.43-44): every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Rear brake linings (check)

Brakes

Factory

Factory: Required work (printed pp.43-44): every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Spoke tension (check)

Wheels and tires

Factory

Factory: Required work (printed pp.43-44): after 1 operating hour (one-time); every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Tire condition (check)

Wheels and tires

Factory

Factory: Required work (printed pp.43-44): after 1 operating hour (one-time); every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Tire pressure (check)

Wheels and tires

Factory

Factory: Required work (printed pp.43-44): after 1 operating hour (one-time); every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Wheel bearing play (check)

Wheels and tires

Factory

Factory: Required work (printed pp.43-44): every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Wheel hubs (check)

Wheels and tires

Factory

Factory: Required work (printed pp.43-44): every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Cables, damage and routing (check)

Controls and cables

Factory

Factory: Required work (printed pp.43-44): every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Throttle cables, damage, routing and setting (check)

Controls and cables

Factory

Factory: Required work (printed pp.43-44): after 1 operating hour (one-time); every 20 operating hours; every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.

Every 40 h

9 items

Electric starter drive (check)

Engine

Factory

Factory: Recommended work (printed pp.44-45): every 40 operating hours; every 80 operating hours. Key: open circle = one-time interval; solid circle = periodic interval.
Gear oil (change)

Engine

Factory

Factory: Required work (printed pp.43-44): after 5 operating hours (one-time); every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Oil screen in the oil tank (clean)

Engine

Factory

Factory: Recommended work (printed pp.44-45): every 40 operating hours. Key: open circle = one-time interval; solid circle = periodic interval.
Piston (change) and cylinder (check)

Engine

Factory

Factory: Recommended work (printed pp.44-45): every 40 operating hours; every 80 operating hours; every 10 operating hours when used for motorsports; every 40 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Pressure sensor protection cap (clean)

Engine

Factory

Factory: Recommended work (printed pp.44-45): every 40 operating hours; every 80 operating hours; every 10 operating hours when used for motorsports; every 40 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Spark plug and spark plug connector (change)

Engine

Factory

Factory: Required work (printed pp.43-44): every 40 operating hours; every 10 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Minor engine service (check exhaust control, check clutch)

Primary and gearbox

Factory

Factory: Recommended work (printed pp.44-45): every 40 operating hours; every 80 operating hours; every 10 operating hours when used for motorsports; every 40 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Fork (service)

Front end

Factory

Factory: Required work (printed pp.43-44): every 40 operating hours. Key: open circle = one-time interval; solid circle = periodic interval.
Shock absorber (service)

Rear suspension and frame

Factory

Factory: Required work (printed pp.43-44): every 40 operating hours. Key: open circle = one-time interval; solid circle = periodic interval.

Every 80 h or 12 months

1 item

Pressure sensor hose (clean)

Engine

Factory

Factory: Recommended work (printed pp.44-45): every 80 operating hours; every 12 months; every 48 months; every 40 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.

Every 80 h

3 items

Major engine service (connecting rod, conrod bearing, crank pin, all engine bearings)

Engine

Factory

Factory: Recommended work (printed pp.44-45): every 80 operating hours; every 40 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.
Oil pump (change), oil screen (clean)

Engine

Factory

Factory: Recommended work (printed pp.44-45): every 80 operating hours. Key: open circle = one-time interval; solid circle = periodic interval.
Fuel filter (change)

Fuel and air

Factory

Factory: Recommended work (printed pp.44-45): every 80 operating hours; every 40 operating hours when used for motorsports. Key: open circle = one-time interval; solid circle = periodic interval.

Every 6 months

1 item

Clean battery terminals, check charge and strap

Ignition and electrics

Guideline

Every 12 months

4 items

Hydraulic clutch fluid (change)

Primary and gearbox

Factory

Factory: Recommended work (printed pp.44-45): every 12 months; every 48 months. Key: open circle = one-time interval; solid circle = periodic interval.
Steering head bearing (lubricate)

Front end

Factory

Factory: Recommended work (printed pp.44-45): every 12 months; every 48 months. Key: open circle = one-time interval; solid circle = periodic interval.
Front brake fluid (change)

Brakes

Factory

Factory: Recommended work (printed pp.44-45): every 12 months; every 48 months. Key: open circle = one-time interval; solid circle = periodic interval.
Rear brake fluid (change)

Brakes

Factory

Factory: Recommended work (printed pp.44-45): every 12 months; every 48 months. Key: open circle = one-time interval; solid circle = periodic interval.

Every 2 years

5 items

Replace coolant

Engine

Guideline
Inspect wiring, bullet connectors and ground points

Ignition and electrics

Guideline
Replace hydraulic clutch fluid

Primary and gearbox

Guideline
Inspect frame, welds and lugs for cracks

Rear suspension and frame

Guideline
Replace brake fluid

Brakes

Guideline

Every 4 years

4 items

Coolant (change)

Engine

Factory

Factory: Recommended work (printed pp.44-45): every 48 months. Key: open circle = one-time interval; solid circle = periodic interval.
Replace fuel lines

Fuel and air

Guideline

Old rubber and modern ethanol fuel do not mix well.
Inspect brake hoses; replace old rubber

Brakes

Guideline
Rebuild calipers and master cylinders (seals)

Brakes

Guideline

Every 6 years

2 items

Replace inner tubes and rim tape with tires

Wheels and tires

Guideline
Replace tires on age (regardless of tread)

Wheels and tires

Guideline

No interval set

2 items

Fork (service, recommended)

Front end

Factory

Factory: Recommended work (printed pp.44-45): after 10 operating hours (one-time). Key: open circle = one-time interval; solid circle = periodic interval.
Shock absorber (service, recommended)

Rear suspension and frame

Factory

Factory: Recommended work (printed pp.44-45): after 20 operating hours (one-time). Key: open circle = one-time interval; solid circle = periodic interval.

Guideline lines: Intervals here are general guidelines for the machine's era and layout, compiled for this app. They are not factory manual figures. Check your workshop manual, and edit any interval in the bike's Schedule tab.