No photo of this model in the library yet.

Have this bike? Send a photo or the manual's service chart

Indian · Hydraulic-lifter four-stroke, wet sump, gearbox shares engine oil, belt drive

101 Scout

Library entry covers 2025

39 factory 45 guideline

Published source

2025 Indian Scout Owner's Manual (P/N 9941836), Periodic Maintenance Table 7.7.5.3 and Maintenance Table Key 7.7.5.2

Factory owner's handbook. Covers 2025 Indian Scout owner's manual P/N 9941836, which covers the Scout Classic, Scout Bobber, Super Scout, Sport Scout and 101 Scout; trim names such as Limited and Tech are not listed separately.

84 items for a 2025 model, grouped by interval the way a factory chart is laid out.

How this bike is built (what the schedule is based on)

Engine cycle: Four-stroke
Engine lubrication: Wet sump (oil in crankcase)
Oil filtration: Replaceable cartridge or spin-on filter
Valve gear: Hydraulic lifters (no routine clearance adjustment)
Ignition: Electronic (CDI / transistor / ECU)
Charging: Alternator / stator with rectifier
Battery: Wet cell (flooded lead-acid, needs topping up)
Fuel system: Fuel injection
Cooling: Liquid cooled
Primary drive: Gear or chain inside engine, shares engine oil
Gearbox oil: Shares engine oil
Clutch control: Hand lever, cable
Final drive: Toothed belt
Front suspension: Telescopic fork
Rear suspension: Swingarm, twin shocks
Front brake: Disc, hydraulic
Rear brake: Disc, hydraulic
Wheels: Cast / alloy, tubeless
Sidecar: No sidecar

Maintenance schedule

2025 Indian 101 Scout

On the road: every 300 km

1 item

Check engine oil level

Pre-ride / on the road

Guideline

Each fuel stop on old machines. Dry sump: check the tank hot, engine idling or just stopped, per your manual.

On the road: every 500 km

2 items

Check lights, horn, brake light switches

Pre-ride / on the road

Guideline
Check tire pressures

Pre-ride / on the road

Guideline

On the road: every 800 km

1 item

Check coolant level

Pre-ride / on the road

Guideline

Every 1,600 km or 6 months

1 item

Inspect tire tread, sidewalls and date codes

Wheels and tires

Guideline

Every 5,000 km or 12 months

7 items

Check throttle cable(s) free play and return

Fuel and air

Guideline
Check steering head bearing adjustment

Front end

Guideline
Inspect fork seals, stanchions and fork boots

Front end

Guideline
Check footrests, pegs, rear brake and gear lever pivots

Rear suspension and frame

Guideline
Grease and check center / side stand and springs

Rear suspension and frame

Guideline
Check brake pads and discs

Brakes

Guideline
Check wheel bearings for play

Wheels and tires

Guideline

Every 6,500 km or 12 months

2 items

Inspect, clean and gap spark plugs

Engine

Guideline
Adjust clutch free play, lubricate cable and lever pivot

Primary and gearbox

Guideline

Every 8,000 km or 12 months

3 items

Change engine oil

Engine

Guideline

Pre-1970 machines: many owners run non-detergent or classic-spec oil with no filter, so short intervals matter. Dry sump: drain the tank and the crankcase/sump, flush the tank and clean the feed and return screens.
Replace oil filter

Engine

Guideline
Inspect drive belt, pulleys and tension

Final drive

Guideline

Every 8,000 km

20 items

Cooling System / Radiator (inspect)

Engine

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: I at 500 mi; I at 2,500 mi; I at 5,000 mi; I at 10,000 mi; I at 15,000 mi; I at 20,000 mi; I at 25,000 mi; I at 30,000 mi; I at 35,000 mi; I at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).
Crankcase Ventilation System (inspect)

Engine

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: I at 500 mi; I at 2,500 mi; I at 5,000 mi; I at 10,000 mi; I at 15,000 mi; I at 20,000 mi; I at 25,000 mi; I at 30,000 mi; I at 35,000 mi; I at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).
Drive Belt (inspect)

Engine

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: I at 500 mi; I at 2,500 mi; I at 5,000 mi; I at 10,000 mi; I at 15,000 mi; I at 20,000 mi; I at 25,000 mi; R at 30,000 mi; I at 35,000 mi; I at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).
Engine Coolant (inspect)

Engine

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: I at 500 mi; I at 2,500 mi; I at 5,000 mi; I at 10,000 mi; I at 15,000 mi; I at 20,000 mi; I at 25,000 mi; I at 30,000 mi; I at 35,000 mi; I at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).
Fasteners (inspect)

Engine

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: I at 500 mi; I at 2,500 mi; I at 5,000 mi; I at 10,000 mi; I at 15,000 mi; I at 20,000 mi; I at 25,000 mi; I at 30,000 mi; I at 35,000 mi; I at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).
Road Test

Engine

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: P at 500 mi; P at 2,500 mi; P at 5,000 mi; P at 10,000 mi; P at 15,000 mi; P at 20,000 mi; P at 25,000 mi; P at 30,000 mi; P at 35,000 mi; P at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).
Fuel System (inspect)

Fuel and air

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: I at 500 mi; I at 2,500 mi; I at 5,000 mi; I at 10,000 mi; I at 15,000 mi; I at 20,000 mi; I at 25,000 mi; I at 30,000 mi; I at 35,000 mi; I at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).
Battery (inspect)

Ignition and electrics

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: I at 500 mi; I at 2,500 mi; I at 5,000 mi; I at 10,000 mi; I at 15,000 mi; I at 20,000 mi; I at 25,000 mi; I at 30,000 mi; I at 35,000 mi; I at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).
Front Fork Oil / Seals (inspect)

Front end

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: I at 500 mi; I at 5,000 mi; I at 10,000 mi; R at 15,000 mi; I at 20,000 mi; I at 25,000 mi; R at 30,000 mi; I at 35,000 mi; I at 40,000 mi. Footnote **: replace at the specified interval or every 2 years. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).
Front Forks and Front Axle (inspect)

Front end

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: I at 500 mi; I at 2,500 mi; I at 5,000 mi; I at 10,000 mi; I at 15,000 mi; I at 20,000 mi; I at 25,000 mi; I at 30,000 mi; I at 35,000 mi; I at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).
Steering Bearings (inspect)

Front end

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: I at 500 mi; I at 2,500 mi; I at 5,000 mi; I at 10,000 mi; I at 15,000 mi; I at 20,000 mi; I at 25,000 mi; I at 30,000 mi; I at 35,000 mi; I at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).
Rear Shock, Bushings, and Fasteners (inspect)

Rear suspension and frame

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: I at 500 mi; I at 2,500 mi; I at 5,000 mi; I at 10,000 mi; I at 15,000 mi; I at 20,000 mi; I at 25,000 mi; I at 30,000 mi; I at 35,000 mi; R at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).
Sidestand / Sidestand Safety Switch (inspect)

Rear suspension and frame

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: L at 500 mi; I at 2,500 mi; L at 5,000 mi; I at 10,000 mi; I at 15,000 mi; I at 20,000 mi; I at 25,000 mi; I at 30,000 mi; I at 35,000 mi; I at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).
Swing Arm, Rear Axle, Swing Arm Pivot, and Pivot Bearings (inspect)

Rear suspension and frame

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: I at 500 mi; I at 2,500 mi; I at 5,000 mi; I at 10,000 mi; I at 15,000 mi; I at 20,000 mi; I at 25,000 mi; I at 30,000 mi; I at 35,000 mi; I at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).
Brake Lever / Pedal (lubricate)

Brakes

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: L at 500 mi; L at 2,500 mi; L at 5,000 mi; L at 10,000 mi; L at 15,000 mi; L at 20,000 mi; L at 25,000 mi; L at 30,000 mi; L at 35,000 mi; L at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).
Brake Pads (inspect)

Brakes

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: I at 500 mi; I at 2,500 mi; I at 5,000 mi; I at 10,000 mi; I at 15,000 mi; I at 20,000 mi; I at 25,000 mi; I at 30,000 mi; I at 35,000 mi; I at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).
Rear Wheel Alignment (inspect)

Wheels and tires

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: I at 500 mi; I at 2,500 mi; I at 5,000 mi; I at 10,000 mi; I at 15,000 mi; I at 20,000 mi; I at 25,000 mi; I at 30,000 mi; I at 35,000 mi; I at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).
Tires / Wheels (inspect)

Wheels and tires

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: I at 500 mi; I at 2,500 mi; I at 5,000 mi; I at 10,000 mi; I at 15,000 mi; I at 20,000 mi; I at 25,000 mi; I at 30,000 mi; I at 35,000 mi; I at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).
Evaporative Emission Control System (If Equipped) (inspect)

Controls and cables

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: I at 500 mi; I at 2,500 mi; I at 5,000 mi; I at 10,000 mi; I at 15,000 mi; I at 20,000 mi; I at 25,000 mi; I at 30,000 mi; I at 35,000 mi; I at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).
Gear Shift Lever (lubricate)

Controls and cables

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: L at 500 mi; L at 2,500 mi; L at 5,000 mi; L at 10,000 mi; L at 15,000 mi; L at 20,000 mi; L at 25,000 mi; L at 30,000 mi; L at 35,000 mi; L at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).

Every 9,500 km or 12 months

7 items

Inspect coolant hoses and clamps

Engine

Guideline
Clean / inspect air filter

Fuel and air

Guideline

Mesh or oiled foam: clean and re-oil. Paper: blow out or replace. Some very early machines have no filter at all.
Check charging voltage and regulator / cut-out

Ignition and electrics

Guideline
Check swingarm bushes for play

Rear suspension and frame

Guideline
Inspect rear shocks for leaks and damping

Rear suspension and frame

Guideline
Lubricate control cables and lever pivots

Controls and cables

Guideline
Lubricate speedometer / tachometer cables, check drive

Controls and cables

Guideline

A dry speedo cable whips the needle and eventually kills the instrument.

Every 16,000 km or 12 months

2 items

Engine Oil (replace)

Engine

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: R at 500 mi; R at 10,000 mi; R at 20,000 mi; R at 30,000 mi; R at 40,000 mi. Footnote *: replace at the specified interval or annually, if driven in extreme conditions. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).
Engine Oil Filter (replace)

Engine

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: R at 500 mi; R at 10,000 mi; R at 20,000 mi; R at 30,000 mi; R at 40,000 mi. Footnote *: replace at the specified interval or annually, if driven in extreme conditions. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).

Every 16,000 km or 2 years

2 items

Compression test (or leak-down)

Engine

Guideline
Brake Fluid (replace)

Brakes

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: I at 500 mi; I at 2,500 mi; I at 5,000 mi; R at 10,000 mi; I at 15,000 mi; R at 20,000 mi; I at 25,000 mi; R at 30,000 mi; I at 35,000 mi; R at 40,000 mi. Footnote **: replace at the specified interval or every 2 years. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).

Every 16,000 km

7 items

Check and Re-Torque Exhaust Joints

Engine

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: P at 500 mi; P at 5,000 mi; P at 10,000 mi; P at 20,000 mi; P at 30,000 mi; P at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).
Head Light (inspect)

Engine

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: I at 500 mi; I at 2,500 mi; I at 10,000 mi; I at 20,000 mi; I at 30,000 mi; I at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).
Air Filter (inspect)

Fuel and air

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: I at 5,000 mi; R at 10,000 mi; I at 15,000 mi; R at 20,000 mi; I at 25,000 mi; R at 30,000 mi; I at 35,000 mi; R at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).
Air Filter (replace)

Fuel and air

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: I at 5,000 mi; R at 10,000 mi; I at 15,000 mi; R at 20,000 mi; I at 25,000 mi; R at 30,000 mi; I at 35,000 mi; R at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).
Clutch Lever / Cable (inspect)

Primary and gearbox

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: L at 500 mi; L at 2,500 mi; L at 5,000 mi; L at 10,000 mi; I at 15,000 mi; L at 20,000 mi; I at 25,000 mi; L at 30,000 mi; I at 35,000 mi; L at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).
Clutch Lever / Cable (lubricate)

Primary and gearbox

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: L at 500 mi; L at 2,500 mi; L at 5,000 mi; L at 10,000 mi; I at 15,000 mi; L at 20,000 mi; I at 25,000 mi; L at 30,000 mi; I at 35,000 mi; L at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).
Brake Fluid (inspect)

Brakes

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: I at 500 mi; I at 2,500 mi; I at 5,000 mi; R at 10,000 mi; I at 15,000 mi; R at 20,000 mi; I at 25,000 mi; R at 30,000 mi; I at 35,000 mi; R at 40,000 mi. Footnote **: replace at the specified interval or every 2 years. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).

Every 19,500 km or 2 years

3 items

Replace air filter element

Fuel and air

Guideline
Synchronize throttle bodies

Fuel and air

Guideline
Grease swingarm pivot

Rear suspension and frame

Guideline

Every 24,000 km or 2 years

1 item

Front Fork Oil / Seals (replace)

Front end

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: I at 500 mi; I at 5,000 mi; I at 10,000 mi; R at 15,000 mi; I at 20,000 mi; I at 25,000 mi; R at 30,000 mi; I at 35,000 mi; I at 40,000 mi. Footnote **: replace at the specified interval or every 2 years. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).

Every 24,000 km or 3 years

1 item

Change fork oil

Front end

Guideline

Some early telescopic forks are grease filled or use very small oil quantities. Check your manual.

Every 25,500 km or 4 years

1 item

Replace spark plugs

Engine

Guideline

Every 32,000 km or 4 years

2 items

Repack / replace steering head bearings

Front end

Guideline

Many old machines use loose balls in cups and cones. Taper roller conversions are common.
Repack / replace wheel bearings

Wheels and tires

Guideline

Cup-and-cone and taper roller hubs need periodic repacking and adjustment.

Every 38,500 km or 4 years

1 item

Replace fuel filter

Fuel and air

Guideline

Every 40,000 km or 6 years

1 item

Replace swingarm bushes / bearings

Rear suspension and frame

Guideline

Every 40,000 km

1 item

Fuel Filter (replace)

Fuel and air

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: R at 25,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).

Every 48,000 km

1 item

Drive Belt (replace)

Engine

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: I at 500 mi; I at 2,500 mi; I at 5,000 mi; I at 10,000 mi; I at 15,000 mi; I at 20,000 mi; I at 25,000 mi; R at 30,000 mi; I at 35,000 mi; I at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).

Every 48,500 km or 6 years

1 item

Rebuild forks: seals, bushes, springs

Front end

Guideline

Every 64,000 km

4 items

Engine Compression (inspect)

Engine

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: I at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).
Spark Plugs (replace)

Engine

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: R at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).
Valve Lash Clearance (inspect)

Engine

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: I at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).
Rear Shock, Bushings, and Fasteners (replace)

Rear suspension and frame

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: I at 500 mi; I at 2,500 mi; I at 5,000 mi; I at 10,000 mi; I at 15,000 mi; I at 20,000 mi; I at 25,000 mi; I at 30,000 mi; I at 35,000 mi; R at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).

Every 80,500 km

1 item

Replace drive belt (wear or damage based)

Final drive

Guideline

Every 6 months

1 item

Clean battery terminals, check charge and strap

Ignition and electrics

Guideline

Every 2 years

4 items

Replace coolant

Engine

Guideline
Inspect wiring, bullet connectors and ground points

Ignition and electrics

Guideline
Inspect frame, welds and lugs for cracks

Rear suspension and frame

Guideline
Replace brake fluid

Brakes

Guideline

Every 4 years

3 items

Replace fuel lines

Fuel and air

Guideline

Old rubber and modern ethanol fuel do not mix well.
Inspect brake hoses; replace old rubber

Brakes

Guideline
Rebuild calipers and master cylinders (seals)

Brakes

Guideline

Every 6 years

1 item

Replace tires on age (regardless of tread)

Wheels and tires

Guideline

No interval set

2 items

Engine Mount Fasteners (inspect)

Engine

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: I at 500 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).
Sidestand / Sidestand Safety Switch (lubricate)

Rear suspension and frame

Factory

Factory: Periodic maintenance table (7.7.5.3), marks as printed: L at 500 mi; I at 2,500 mi; L at 5,000 mi; I at 10,000 mi; I at 15,000 mi; I at 20,000 mi; I at 25,000 mi; I at 30,000 mi; I at 35,000 mi; I at 40,000 mi. Key: I = inspect (tighten, clean, adjust, correct or replace if necessary); R = replace or rebuild; L = lubricate; P = perform. Columns: 500 mi (800 km), 2,500 mi (4,000 km), then every 5,000 mi (8,000 km) to 40,000 mi (64,000 km).

Guideline lines: Intervals here are general guidelines for the machine's era and layout, compiled for this app. They are not factory manual figures. Check your workshop manual, and edit any interval in the bike's Schedule tab.