Indian · Indian Thunderstroke / PowerPlus cruisers (2014-)

FTR 1200 / FTR

Library entry covers 2019-2026

16 factory 31 guideline

Published source

2023 Indian FTR Owner's Manual, P/N 9940927, 7.7.7.2 Maintenance Intervals

Factory owner's handbook. Covers 2023 FTR / FTR Sport / FTR R Carbon.

Open the source

47 items for a 2022 model, grouped by interval the way a factory chart is laid out.

How this bike is built (what the schedule is based on)

Engine cycle: Four-stroke
Engine lubrication: Wet sump (oil in crankcase)
Oil filtration: Replaceable cartridge or spin-on filter
Valve gear: Hydraulic lifters (no routine clearance adjustment)
Ignition: Electronic (CDI / transistor / ECU)
Charging: Alternator / stator with rectifier
Battery: Wet cell (flooded lead-acid, needs topping up)
Fuel system: Fuel injection
Cooling: Air / oil cooled
Primary drive: Gear or chain inside engine, shares engine oil
Gearbox oil: Shares engine oil
Clutch control: Hand lever, cable
Final drive: Chain
Front suspension: Telescopic fork
Rear suspension: Swingarm, twin shocks
Front brake: Disc, hydraulic
Rear brake: Disc, hydraulic
Wheels: Cast / alloy, tubeless
Sidecar: No sidecar

Maintenance schedule

2022 Indian FTR 1200 / FTR

On the road: every 200 mi

1 item

Check engine oil level

Pre-ride / on the road

Guideline

Each fuel stop on old machines. Dry sump: check the tank hot, engine idling or just stopped, per your manual.

On the road: every 300 mi

3 items

Check lights, horn, brake light switches

Pre-ride / on the road

Guideline
Check tire pressures

Pre-ride / on the road

Guideline
Lubricate drive chain

Pre-ride / on the road

Guideline

Lube warm, ideally at the end of the riding day so it soaks in overnight. Sooner after rain.

On the road: every 600 mi

1 item

Check chain slack and rear wheel alignment

Pre-ride / on the road

Guideline

Every 3,000 mi or 12 months

7 items

Check throttle cable(s) free play and return

Fuel and air

Guideline
Clean drive chain thoroughly (remove and soak, re-lube)

Final drive

Guideline

Non O-ring chains on old machines: remove, clean, soak in hot chain grease or lube, refit with the master link clip closed end leading.
Inspect chain and sprockets for wear (measure stretch)

Final drive

Guideline
Inspect fork seals, stanchions and fork boots

Front end

Guideline
Check footrests, pegs, rear brake and gear lever pivots

Rear suspension and frame

Guideline
Grease and check center / side stand and springs

Rear suspension and frame

Guideline
Check wheel bearings for play

Wheels and tires

Guideline

Every 4,000 mi or 12 months

1 item

Adjust clutch free play, lubricate cable and lever pivot

Primary and gearbox

Guideline

Every 5,000 mi

4 items

Clean battery terminals, check charge and strap

Ignition and electrics

Factory

Manual: Battery: Check terminals; clean; test. Factory: Tables 500, 2,500, 5,000 mi then every 5,000 mi to 50,000; cycle repeats.
Check steering head bearing adjustment

Front end

Factory

Manual: Steering Bearings: Inspect. Factory: Tables 500, 2,500, 5,000 mi then every 5,000 mi to 50,000; cycle repeats.
Check brake pads and discs

Brakes

Factory

Manual: Brake Pads: Inspect pad wear. Factory: Tables 500, 2,500, 5,000 mi then every 5,000 mi to 50,000; cycle repeats.
Inspect tire tread, sidewalls and date codes

Wheels and tires

Factory

Manual: Tires / Wheels: Inspect. Factory: Tables 500, 2,500, 5,000 mi then every 5,000 mi to 50,000; cycle repeats.

Every 6,000 mi or 12 months

5 items

Clean / inspect air filter

Fuel and air

Guideline

Mesh or oiled foam: clean and re-oil. Paper: blow out or replace. Some very early machines have no filter at all.
Check charging voltage and regulator / cut-out

Ignition and electrics

Guideline
Check swingarm bushes for play

Rear suspension and frame

Guideline
Lubricate control cables and lever pivots

Controls and cables

Guideline
Lubricate speedometer / tachometer cables, check drive

Controls and cables

Guideline

A dry speedo cable whips the needle and eventually kills the instrument.

Every 10,000 mi or 2 years

1 item

Replace brake fluid

Brakes

Factory

Manual: Brake Fluid: Replace (DOT 4). Factory: Replace at 10k-mile tables; change every two years.

Every 10,000 mi

4 items

Change engine oil

Engine

Factory

Manual: Engine Oil & Filter Change. Factory: At 500 mi, then 10k, 20k, 30k, 40k, 50k mi.
Compression test (or leak-down)

Engine

Factory

Manual: Engine Compression: Inspect. Factory: At 10k, 20k, 30k, 40k, 50k mi.
Inspect, clean and gap spark plugs

Engine

Factory

Manual: Spark Plugs: Inspect; replace as needed. Factory: At 10k, 20k, 40k, 50k mi.
Replace oil filter

Engine

Factory

Manual: Engine Oil & Filter Change. Factory: With oil change.

Every 12,000 mi or 2 years

2 items

Synchronize throttle bodies

Fuel and air

Guideline
Grease swingarm pivot

Rear suspension and frame

Guideline

Every 15,000 mi or 2 years

1 item

Change fork oil

Front end

Factory

Manual: Front Fork Oil: Replace. Factory: Replace at 15k, 30k, 45k mi or every 2 years.

Every 15,000 mi

2 items

Replace air filter element

Fuel and air

Factory

Manual: Air Filter: Replace. Factory: Replace at 15k, 30k, 45k mi; inspect/clean other tables.
Replace chain and sprockets (wear based)

Final drive

Factory

Manual: Drive Chain: Replace. Factory: Replace at 15k, 30k, 45k mi; inspect, clean, lube otherwise.

Every 20,000 mi or 4 years

2 items

Repack / replace steering head bearings

Front end

Guideline

Many old machines use loose balls in cups and cones. Taper roller conversions are common.
Repack / replace wheel bearings

Wheels and tires

Guideline

Cup-and-cone and taper roller hubs need periodic repacking and adjustment.

Every 20,000 mi

1 item

Check and adjust valve clearances

Engine

Factory

Manual: Valve Lash Clearance: Inspect; adjust. Factory: At 20k and 40k mi.

Every 24,000 mi or 4 years

1 item

Replace fuel filter

Fuel and air

Guideline

Every 25,000 mi or 6 years

1 item

Replace swingarm bushes / bearings

Rear suspension and frame

Guideline

Every 30,000 mi or 6 years

1 item

Rebuild forks: seals, bushes, springs

Front end

Guideline

Every 30,000 mi

1 item

Replace spark plugs

Engine

Factory

Manual: Spark Plugs: Replace. Factory: Replace in 30k table only within 50k cycle.

Every 50,000 mi

2 items

Check engine mounting bolts and plates

Engine

Factory

Manual: Engine Mount Fasteners: Inspect; tighten. Factory: At 500 mi and 50k mi.
Inspect rear shocks for leaks and damping

Rear suspension and frame

Factory

Manual: Rear Shock Absorber. Factory: Replace at 50k mi; inspect at all other tables.

Every 2 years

2 items

Inspect wiring, bullet connectors and ground points

Ignition and electrics

Guideline
Inspect frame, welds and lugs for cracks

Rear suspension and frame

Guideline

Every 4 years

3 items

Replace fuel lines

Fuel and air

Guideline

Old rubber and modern ethanol fuel do not mix well.
Inspect brake hoses; replace old rubber

Brakes

Guideline
Rebuild calipers and master cylinders (seals)

Brakes

Guideline

Every 6 years

1 item

Replace tires on age (regardless of tread)

Wheels and tires

Guideline

Guideline lines: Intervals here are general guidelines for the machine's era and layout, compiled for this app. They are not factory manual figures. Check your workshop manual, and edit any interval in the bike's Schedule tab.