Indian FTR 1200 / FTR — Example photo: Decio "desmodex", CC BY-SA 2.0, Wikimedia Commons

Have this bike? Send a photo or the manual's service chart

Indian · Shim-adjusted overhead-cam four-stroke twin, wet sump, gearbox shares engine oil, chain drive

FTR 1200 / FTR

Library entry covers 2019-2026

43 factory 35 guideline

Published source

2023 Indian FTR Owner's Manual, P/N 9940927, 7.7.7.2 Maintenance Intervals

Factory owner's handbook. Covers 2023 FTR / FTR Sport / FTR R Carbon.

78 items for a 2025 model, grouped by interval the way a factory chart is laid out.

How this bike is built (what the schedule is based on)

Engine cycle: Four-stroke
Engine lubrication: Wet sump (oil in crankcase)
Oil filtration: Replaceable cartridge or spin-on filter
Valve gear: Overhead cam, shim adjusted (incl. desmo)
Ignition: Electronic (CDI / transistor / ECU)
Charging: Alternator / stator with rectifier
Battery: Wet cell (flooded lead-acid, needs topping up)
Fuel system: Fuel injection
Cooling: Liquid cooled
Primary drive: Gear or chain inside engine, shares engine oil
Gearbox oil: Shares engine oil
Clutch control: Hand lever, cable
Final drive: Chain
Front suspension: Telescopic fork
Rear suspension: Swingarm, twin shocks
Front brake: Disc, hydraulic
Rear brake: Disc, hydraulic
Wheels: Cast / alloy, tubeless
Sidecar: No sidecar

Maintenance schedule

2025 Indian FTR 1200 / FTR

On the road: every 300 km

1 item

Check engine oil level

Pre-ride / on the road

Guideline

Each fuel stop on old machines. Dry sump: check the tank hot, engine idling or just stopped, per your manual.

On the road: every 500 km

3 items

Check lights, horn, brake light switches

Pre-ride / on the road

Guideline
Check tire pressures

Pre-ride / on the road

Guideline
Lubricate drive chain

Pre-ride / on the road

Guideline

Lube warm, ideally at the end of the riding day so it soaks in overnight. Sooner after rain.

On the road: every 800 km

1 item

Check coolant level

Pre-ride / on the road

Guideline

On the road: every 1,000 km

1 item

Check chain slack and rear wheel alignment

Pre-ride / on the road

Guideline

Every 5,000 km or 12 months

7 items

Check throttle cable(s) free play and return

Fuel and air

Guideline
Clean drive chain thoroughly (remove and soak, re-lube)

Final drive

Guideline

Non O-ring chains on old machines: remove, clean, soak in hot chain grease or lube, refit with the master link clip closed end leading.
Inspect chain and sprockets for wear (measure stretch)

Final drive

Guideline
Inspect fork seals, stanchions and fork boots

Front end

Guideline
Check footrests, pegs, rear brake and gear lever pivots

Rear suspension and frame

Guideline
Grease and check center / side stand and springs

Rear suspension and frame

Guideline
Check wheel bearings for play

Wheels and tires

Guideline

Every 6,500 km or 12 months

1 item

Adjust clutch free play, lubricate cable and lever pivot

Primary and gearbox

Guideline

Every 8,000 km

27 items

Crankcase Ventilation System

Engine

Factory

Factory: As printed: 'Inspect; tighten, clean, adjust' in every interval table (500 mi / 800 km, 2,500 mi / 4,000 km, 5,000 mi / 8,000 km, then every 5,000 mi to 50,000 mi / 80,000 km; charts then restart at 500 mi); code D
Driver and Passenger Pegs

Engine

Factory

Factory: As printed: 'Inspect; lubricate if necessary' in every interval table (500 mi / 800 km, 2,500 mi / 4,000 km, 5,000 mi / 8,000 km, then every 5,000 mi to 50,000 mi / 80,000 km; charts then restart at 500 mi); code D
Exhaust System

Engine

Factory

Factory: As printed: 'Inspect; tighten, adjust' in every interval table (500 mi / 800 km, 2,500 mi / 4,000 km, 5,000 mi / 8,000 km, then every 5,000 mi to 50,000 mi / 80,000 km; charts then restart at 500 mi); code E
Fasteners

Engine

Factory

Factory: As printed: 'Inspect; tighten if necessary' in every interval table (500 mi / 800 km, 2,500 mi / 4,000 km, 5,000 mi / 8,000 km, then every 5,000 mi to 50,000 mi / 80,000 km; charts then restart at 500 mi); code D
Gear Shift Pedal

Engine

Factory

Factory: As printed: 'Inspect; lubricate, adjust if necessary' in every interval table (500 mi / 800 km, 2,500 mi / 4,000 km, 5,000 mi / 8,000 km, then every 5,000 mi to 50,000 mi / 80,000 km; charts then restart at 500 mi); code D
Oil Lines / Oil System Inspection

Engine

Factory

Factory: As printed: 'Inspect; clean, adjust if necessary' in every interval table (500 mi / 800 km, 2,500 mi / 4,000 km, 5,000 mi / 8,000 km, then every 5,000 mi to 50,000 mi / 80,000 km; charts then restart at 500 mi); code D
Road Test

Engine

Factory

Factory: As printed: 'Perform Road Test' in every interval table (500 mi / 800 km, 2,500 mi / 4,000 km, 5,000 mi / 8,000 km, then every 5,000 mi to 50,000 mi / 80,000 km; charts then restart at 500 mi); code (blank)
Suspension Linkage, Rear

Engine

Factory

Factory: As printed: 'Inspect' in every interval table (500 mi / 800 km, 2,500 mi / 4,000 km, 5,000 mi / 8,000 km, then every 5,000 mi to 50,000 mi / 80,000 km; charts then restart at 500 mi); code D
Air Filter: Inspect; clean

Fuel and air

Factory

Factory: As printed: 'Inspect; clean' in the 2,500, 5,000, 10,000, 20,000, 25,000, 35,000, 40,000, 50,000 mi tables (replaced at 15,000, 30,000, 45,000 mi); code XU
Fuel System

Fuel and air

Factory

Factory: As printed: 'Inspect; clean' in every interval table (500 mi / 800 km, 2,500 mi / 4,000 km, 5,000 mi / 8,000 km, then every 5,000 mi to 50,000 mi / 80,000 km; charts then restart at 500 mi); code D
Clean battery terminals, check charge and strap

Ignition and electrics

Factory

Manual: Battery: Check terminals; clean; test. Factory: Tables 500, 2,500, 5,000 mi then every 5,000 mi to 50,000; cycle repeats.
Clutch Cable Freeplay

Primary and gearbox

Factory

Factory: As printed: 'Inspect; adjust if necessary' in every interval table (500 mi / 800 km, 2,500 mi / 4,000 km, 5,000 mi / 8,000 km, then every 5,000 mi to 50,000 mi / 80,000 km; charts then restart at 500 mi); code D
Clutch Lever

Primary and gearbox

Factory

Factory: As printed: 'Lubricate with proper lubricant as directed' in the 500 mi table and the 5,000 mi table and every 5,000 mi table after (not 2,500); code D
Chain Sliders: Inspect

Final drive

Factory

Factory: As printed: 'Inspect; replace as needed' in the 5,000 mi table and every 5,000 mi table after (not 500 or 2,500); code D
Drive Chain: Inspect; clean, lubricate

Final drive

Factory

Factory: As printed: 'Inspect; clean, lubricate' in every interval table (500 mi / 800 km, 2,500 mi / 4,000 km, 5,000 mi / 8,000 km, then every 5,000 mi to 50,000 mi / 80,000 km; charts then restart at 500 mi); code D
Check steering head bearing adjustment

Front end

Factory

Manual: Steering Bearings: Inspect. Factory: Tables 500, 2,500, 5,000 mi then every 5,000 mi to 50,000; cycle repeats.
Front Forks and Front Axle

Front end

Factory

Factory: As printed: 'Inspect; adjust if necessary' in every interval table (500 mi / 800 km, 2,500 mi / 4,000 km, 5,000 mi / 8,000 km, then every 5,000 mi to 50,000 mi / 80,000 km; charts then restart at 500 mi); code D
Rear Shock Absorber: Inspect; adjust if necessary

Rear suspension and frame

Factory

Factory: Printed per the re-read doubt: Rear Shock Absorber prints 'Inspect; adjust if necessary' in each table and is replaced (D) at 50,000 mi; the tables are 500 mi, 2,500 mi, 5,000 mi, then every 5,000 mi, taken as inspect every 5,000 mi (8,000 km). The existing entry holds the replace. (From the re-read doubt notes: Indian FTR 1200 / FTR, printed line or second operation stated in the DOUBT line.)
Sidestand

Rear suspension and frame

Factory

Factory: As printed: 'Lubricate with proper lubricant as directed' in every interval table (500 mi / 800 km, 2,500 mi / 4,000 km, 5,000 mi / 8,000 km, then every 5,000 mi to 50,000 mi / 80,000 km; charts then restart at 500 mi); code D
Swing Arm and Rear Axle

Rear suspension and frame

Factory

Factory: As printed: 'Inspect' in every interval table (500 mi / 800 km, 2,500 mi / 4,000 km, 5,000 mi / 8,000 km, then every 5,000 mi to 50,000 mi / 80,000 km; charts then restart at 500 mi); code D
Check brake pads and discs

Brakes

Factory

Manual: Brake Pads: Inspect pad wear. Factory: Tables 500, 2,500, 5,000 mi then every 5,000 mi to 50,000; cycle repeats.
Front Brake Lever

Brakes

Factory

Factory: As printed: 'Adjust if necessary, lubricate with proper lubricant as directed' in every interval table (500 mi / 800 km, 2,500 mi / 4,000 km, 5,000 mi / 8,000 km, then every 5,000 mi to 50,000 mi / 80,000 km; charts then restart at 500 mi); code D
Rear Brake Pedal

Brakes

Factory

Factory: As printed: 'Inspect; lubricate, adjust if necessary' in every interval table (500 mi / 800 km, 2,500 mi / 4,000 km, 5,000 mi / 8,000 km, then every 5,000 mi to 50,000 mi / 80,000 km; charts then restart at 500 mi); code D
Inspect tire tread, sidewalls and date codes

Wheels and tires

Factory

Manual: Tires / Wheels: Inspect. Factory: Tables 500, 2,500, 5,000 mi then every 5,000 mi to 50,000; cycle repeats.
Rear Wheel Alignment

Wheels and tires

Factory

Factory: As printed: 'Inspect; adjust if necessary' in every interval table (500 mi / 800 km, 2,500 mi / 4,000 km, 5,000 mi / 8,000 km, then every 5,000 mi to 50,000 mi / 80,000 km; charts then restart at 500 mi); code D
Control Cable Ends

Controls and cables

Factory

Factory: As printed: 'Lubricate with proper lubricant as directed' in the 500 mi table and the 5,000 mi table and every 5,000 mi table after (not 2,500); code D
Evaporative Emission Control System

Controls and cables

Factory

Factory: As printed: 'Inspect; clean' in every interval table (500 mi / 800 km, 2,500 mi / 4,000 km, 5,000 mi / 8,000 km, then every 5,000 mi to 50,000 mi / 80,000 km; charts then restart at 500 mi); code E

Every 9,500 km or 12 months

6 items

Inspect coolant hoses and clamps

Engine

Guideline
Clean / inspect air filter

Fuel and air

Guideline

Mesh or oiled foam: clean and re-oil. Paper: blow out or replace. Some very early machines have no filter at all.
Check charging voltage and regulator / cut-out

Ignition and electrics

Guideline
Check swingarm bushes for play

Rear suspension and frame

Guideline
Lubricate control cables and lever pivots

Controls and cables

Guideline
Lubricate speedometer / tachometer cables, check drive

Controls and cables

Guideline

A dry speedo cable whips the needle and eventually kills the instrument.

Every 16,000 km or 2 years

1 item

Replace brake fluid

Brakes

Factory

Manual: Brake Fluid: Replace (DOT 4). Factory: Replace at 10k-mile tables; change every two years.

Every 16,000 km

5 items

Change engine oil

Engine

Factory

Manual: Engine Oil & Filter Change. Factory: At 500 mi, then 10k, 20k, 30k, 40k, 50k mi.
Compression test (or leak-down)

Engine

Factory

Manual: Engine Compression: Inspect. Factory: At 10k, 20k, 30k, 40k, 50k mi.
Head Light

Engine

Factory

Factory: As printed: 'Inspect; adjust if necessary' in the 500, 2,500, 10,000, 20,000, 30,000, 40,000, 50,000 mi tables; code D
Inspect, clean and gap spark plugs

Engine

Factory

Manual: Spark Plugs: Inspect; replace as needed. Factory: At 10k, 20k, 40k, 50k mi.
Replace oil filter

Engine

Factory

Manual: Engine Oil & Filter Change. Factory: With oil change.

Every 19,500 km or 2 years

2 items

Synchronize throttle bodies

Fuel and air

Guideline
Grease swingarm pivot

Rear suspension and frame

Guideline

Every 24,000 km or 2 years

1 item

Change fork oil

Front end

Factory

Manual: Front Fork Oil: Replace. Factory: Replace at 15k, 30k, 45k mi or every 2 years.

Every 24,000 km or 4 years

1 item

Check valve clearances (shim adjusted)

Engine

Guideline

Every 24,000 km

2 items

Replace air filter element

Fuel and air

Factory

Manual: Air Filter: Replace. Factory: Replace at 15k, 30k, 45k mi; inspect/clean other tables.
Replace chain and sprockets (wear based)

Final drive

Factory

Manual: Drive Chain: Replace. Factory: Replace at 15k, 30k, 45k mi; inspect, clean, lube otherwise.

Every 32,000 km or 4 years

2 items

Repack / replace steering head bearings

Front end

Guideline

Many old machines use loose balls in cups and cones. Taper roller conversions are common.
Repack / replace wheel bearings

Wheels and tires

Guideline

Cup-and-cone and taper roller hubs need periodic repacking and adjustment.

Every 32,000 km

1 item

Check and adjust valve clearances

Engine

Factory

Manual: Valve Lash Clearance: Inspect; adjust. Factory: At 20k and 40k mi.

Every 38,500 km or 4 years

1 item

Replace fuel filter

Fuel and air

Guideline

Every 40,000 km or 6 years

1 item

Replace swingarm bushes / bearings

Rear suspension and frame

Guideline

Every 48,000 km

1 item

Replace spark plugs

Engine

Factory

Manual: Spark Plugs: Replace. Factory: Replace in 30k table only within 50k cycle.

Every 48,500 km or 6 years

1 item

Rebuild forks: seals, bushes, springs

Front end

Guideline

Every 80,000 km

2 items

Check engine mounting bolts and plates

Engine

Factory

Manual: Engine Mount Fasteners: Inspect; tighten. Factory: At 500 mi and 50k mi.
Inspect rear shocks for leaks and damping

Rear suspension and frame

Factory

Manual: Rear Shock Absorber. Factory: Replace at 50k mi; inspect at all other tables.

Every 2 years

3 items

Replace coolant

Engine

Guideline
Inspect wiring, bullet connectors and ground points

Ignition and electrics

Guideline
Inspect frame, welds and lugs for cracks

Rear suspension and frame

Guideline

Every 4 years

3 items

Replace fuel lines

Fuel and air

Guideline

Old rubber and modern ethanol fuel do not mix well.
Inspect brake hoses; replace old rubber

Brakes

Guideline
Rebuild calipers and master cylinders (seals)

Brakes

Guideline

Every 6 years

1 item

Replace tires on age (regardless of tread)

Wheels and tires

Guideline

No interval set

3 items

Chain Sliders: replace

Final drive

Factory

Factory: As printed: replace as needed
Front Fork Oil: Inspect

Front end

Factory

Factory: Printed per the re-read doubt: the 500, 20,000, 25,000, 35,000 mi tables print Front fork oil as inspect; irregular, so no single interval. The existing entry holds the replace. (From the re-read doubt notes: Indian FTR 1200 / FTR, printed line or second operation stated in the DOUBT line.)
Brake Pads: replace

Brakes

Factory

Factory: As printed: replace if worn beyond service limit

Guideline lines: Intervals here are general guidelines for the machine's era and layout, compiled for this app. They are not factory manual figures. Check your workshop manual, and edit any interval in the bike's Schedule tab.