No photo of this model in the library yet.

Have this bike? Send a photo or the manual's service chart

Kymco · Overhead-cam four-stroke single, wet sump, separate gearbox oil, CVT belt drive

Agility 125

Library entry covers 2009-2024

14 factory 48 guideline

Published source

KYMCO Agility 125 Service Manual, maintenance schedule p.3-2 (ManualsLib viewer p.36)

Factory service manual. Covers KYMCO Agility 125 service manual (ManualsLib title; table labeled AGILITY 125), no year seen; carburetor-era version, later fuel-injected models not compared.

62 items for a 2021 model, grouped by interval the way a factory chart is laid out.

How this bike is built (what the schedule is based on)

Engine cycle: Four-stroke
Engine lubrication: Wet sump (oil in crankcase)
Oil filtration: Replaceable cartridge or spin-on filter
Valve gear: Overhead cam, screw/locknut adjusters
Ignition: Electronic (CDI / transistor / ECU)
Charging: Alternator / stator with rectifier
Battery: Wet cell (flooded lead-acid, needs topping up)
Fuel system: Fuel injection
Cooling: Air / oil cooled
Primary drive: Gear or chain inside engine, shares engine oil
Gearbox oil: Separate gearbox oil
Clutch control: Automatic or semi-automatic
Final drive: Belt CVT, scooter automatic
Front suspension: Telescopic fork
Rear suspension: Swingarm, single shock / cantilever
Front brake: Disc, hydraulic
Rear brake: Drum (or band / belt rim)
Wheels: Cast / alloy, tubeless
Sidecar: No sidecar

Maintenance schedule

2021 Kymco Agility 125

On the road: every 300 km

1 item

Check engine oil level

Pre-ride / on the road

Guideline

Each fuel stop on old machines. Dry sump: check the tank hot, engine idling or just stopped, per your manual.

On the road: every 500 km

2 items

Check lights, horn, brake light switches

Pre-ride / on the road

Guideline
Check tire pressures

Pre-ride / on the road

Guideline

Every 1,000 km

1 item

Brake system (inspect)

Brakes

Factory

Factory: Maintenance schedule (p.3-2, AGILITY 125): I every 1,000 km. Columns as printed: 300 km (new motorcycle), then every 1,000 km to 12,000 km, whichever comes first; for higher readings repeat the same frequency. Key: I inspect (clean, adjust, lubricate or replace if necessary), A adjust, C clean, R replace, T tighten. Service more often in dusty or rainy areas, or in rain or at full throttle. This is a carburetor-era service manual.

Every 1,600 km or 6 months

2 items

Adjust rear drum brake and rod / cable linkage

Brakes

Guideline
Inspect tire tread, sidewalls and date codes

Wheels and tires

Guideline

Every 2,000 km

2 items

Engine oil (replace)

Engine

Factory

Factory: Maintenance schedule (p.3-2, AGILITY 125): R at 300 km on a new motorcycle, then every 2,000 km. Columns as printed: 300 km (new motorcycle), then every 1,000 km to 12,000 km, whichever comes first; for higher readings repeat the same frequency. Key: I inspect (clean, adjust, lubricate or replace if necessary), A adjust, C clean, R replace, T tighten. Service more often in dusty or rainy areas, or in rain or at full throttle. This is a carburetor-era service manual.
Air cleaner (replace)

Fuel and air

Factory

Factory: Maintenance schedule (p.3-2, AGILITY 125): replace every 2,000 km (notes 2 and 3). Columns as printed: 300 km (new motorcycle), then every 1,000 km to 12,000 km, whichever comes first; for higher readings repeat the same frequency. Key: I inspect (clean, adjust, lubricate or replace if necessary), A adjust, C clean, R replace, T tighten. Service more often in dusty or rainy areas, or in rain or at full throttle. This is a carburetor-era service manual.

Every 3,000 km

1 item

Spark plug (clean)

Engine

Factory

Factory: Maintenance schedule (p.3-2, AGILITY 125): clean every 3,000 km and replace if necessary. Columns as printed: 300 km (new motorcycle), then every 1,000 km to 12,000 km, whichever comes first; for higher readings repeat the same frequency. Key: I inspect (clean, adjust, lubricate or replace if necessary), A adjust, C clean, R replace, T tighten. Service more often in dusty or rainy areas, or in rain or at full throttle. This is a carburetor-era service manual.

Every 4,000 km

5 items

Engine oil filter screen (clean)

Engine

Factory

Factory: Maintenance schedule (p.3-2, AGILITY 125): C at 4,000 and 8,000 km. Columns as printed: 300 km (new motorcycle), then every 1,000 km to 12,000 km, whichever comes first; for higher readings repeat the same frequency. Key: I inspect (clean, adjust, lubricate or replace if necessary), A adjust, C clean, R replace, T tighten. Service more often in dusty or rainy areas, or in rain or at full throttle. This is a carburetor-era service manual.
Suspension (inspect)

Engine

Factory

Factory: Maintenance schedule (p.3-2, AGILITY 125): I at 4,000, 8,000 and 12,000 km. Columns as printed: 300 km (new motorcycle), then every 1,000 km to 12,000 km, whichever comes first; for higher readings repeat the same frequency. Key: I inspect (clean, adjust, lubricate or replace if necessary), A adjust, C clean, R replace, T tighten. Service more often in dusty or rainy areas, or in rain or at full throttle. This is a carburetor-era service manual.
Valve clearance (adjust)

Engine

Factory

Factory: Maintenance schedule (p.3-2, AGILITY 125): A at 2,000, 4,000, 8,000 and 12,000 km. Columns as printed: 300 km (new motorcycle), then every 1,000 km to 12,000 km, whichever comes first; for higher readings repeat the same frequency. Key: I inspect (clean, adjust, lubricate or replace if necessary), A adjust, C clean, R replace, T tighten. Service more often in dusty or rainy areas, or in rain or at full throttle. This is a carburetor-era service manual.
Carburetor (inspect, clean)

Fuel and air

Factory

Factory: Maintenance schedule (p.3-2, AGILITY 125): I at 4,000 and 8,000 km; C at 12,000 km. Columns as printed: 300 km (new motorcycle), then every 1,000 km to 12,000 km, whichever comes first; for higher readings repeat the same frequency. Key: I inspect (clean, adjust, lubricate or replace if necessary), A adjust, C clean, R replace, T tighten. Service more often in dusty or rainy areas, or in rain or at full throttle. This is a carburetor-era service manual.
Tires (inspect)

Wheels and tires

Factory

Factory: Maintenance schedule (p.3-2, AGILITY 125): I at 4,000, 8,000 and 12,000 km. Columns as printed: 300 km (new motorcycle), then every 1,000 km to 12,000 km, whichever comes first; for higher readings repeat the same frequency. Key: I inspect (clean, adjust, lubricate or replace if necessary), A adjust, C clean, R replace, T tighten. Service more often in dusty or rainy areas, or in rain or at full throttle. This is a carburetor-era service manual.

Every 5,000 km or 12 months

8 items

Check throttle cable(s) free play and return

Fuel and air

Guideline
Adjust automatic / semi-automatic clutch

Primary and gearbox

Guideline
Check steering head bearing adjustment

Front end

Guideline
Inspect fork seals, stanchions and fork boots

Front end

Guideline
Check footrests, pegs, rear brake and gear lever pivots

Rear suspension and frame

Guideline
Grease and check center / side stand and springs

Rear suspension and frame

Guideline
Check brake pads and discs

Brakes

Guideline
Check wheel bearings for play

Wheels and tires

Guideline

Every 5,000 km

1 item

Gear oil (replace)

Engine

Factory

Factory: Maintenance schedule (p.3-2, AGILITY 125): R at 300 km on a new motorcycle, then at 5,000 and 10,000 km. Columns as printed: 300 km (new motorcycle), then every 1,000 km to 12,000 km, whichever comes first; for higher readings repeat the same frequency. Key: I inspect (clean, adjust, lubricate or replace if necessary), A adjust, C clean, R replace, T tighten. Service more often in dusty or rainy areas, or in rain or at full throttle. This is a carburetor-era service manual.

Every 6,000 km

1 item

Steering head bearing (inspect)

Front end

Factory

Factory: Maintenance schedule (p.3-2, AGILITY 125): I at 1,000, 6,000 and 12,000 km. Columns as printed: 300 km (new motorcycle), then every 1,000 km to 12,000 km, whichever comes first; for higher readings repeat the same frequency. Key: I inspect (clean, adjust, lubricate or replace if necessary), A adjust, C clean, R replace, T tighten. Service more often in dusty or rainy areas, or in rain or at full throttle. This is a carburetor-era service manual.

Every 6,500 km or 12 months

3 items

Inspect, clean and gap spark plugs

Engine

Guideline
Inspect CVT drive belt, rollers / sliders and clutch shoes

Final drive

Guideline

Typical scooter interval. Your owner's manual figure governs; check belt width against the service limit.
Lubricate brake cam spindles, check linings and drums

Brakes

Guideline

Every 8,000 km or 12 months

2 items

Change engine oil

Engine

Guideline

Pre-1970 machines: many owners run non-detergent or classic-spec oil with no filter, so short intervals matter. Dry sump: drain the tank and the crankcase/sump, flush the tank and clean the feed and return screens.
Replace oil filter

Engine

Guideline

Every 8,000 km

2 items

Drive belt (inspect)

Engine

Factory

Factory: Maintenance schedule (p.3-2, AGILITY 125): I at 8,000 km. Columns as printed: 300 km (new motorcycle), then every 1,000 km to 12,000 km, whichever comes first; for higher readings repeat the same frequency. Key: I inspect (clean, adjust, lubricate or replace if necessary), A adjust, C clean, R replace, T tighten. Service more often in dusty or rainy areas, or in rain or at full throttle. This is a carburetor-era service manual.
Nuts, bolts and fasteners (inspect)

Engine

Factory

Factory: Maintenance schedule (p.3-2, AGILITY 125): I at 8,000 km. Columns as printed: 300 km (new motorcycle), then every 1,000 km to 12,000 km, whichever comes first; for higher readings repeat the same frequency. Key: I inspect (clean, adjust, lubricate or replace if necessary), A adjust, C clean, R replace, T tighten. Service more often in dusty or rainy areas, or in rain or at full throttle. This is a carburetor-era service manual.

Every 9,500 km or 12 months

6 items

Clean / inspect air filter

Fuel and air

Guideline

Mesh or oiled foam: clean and re-oil. Paper: blow out or replace. Some very early machines have no filter at all.
Check charging voltage and regulator / cut-out

Ignition and electrics

Guideline
Check swingarm bushes for play

Rear suspension and frame

Guideline
Inspect rear shocks for leaks and damping

Rear suspension and frame

Guideline
Lubricate control cables and lever pivots

Controls and cables

Guideline
Lubricate speedometer / tachometer cables, check drive

Controls and cables

Guideline

A dry speedo cable whips the needle and eventually kills the instrument.

Every 10,000 km

1 item

Fuel filter screen (replace)

Fuel and air

Factory

Factory: Maintenance schedule (p.3-2, AGILITY 125): R at 10,000 km. Columns as printed: 300 km (new motorcycle), then every 1,000 km to 12,000 km, whichever comes first; for higher readings repeat the same frequency. Key: I inspect (clean, adjust, lubricate or replace if necessary), A adjust, C clean, R replace, T tighten. Service more often in dusty or rainy areas, or in rain or at full throttle. This is a carburetor-era service manual.

Every 13,000 km or 2 years

1 item

Check and adjust valve clearances

Engine

Guideline

Every 16,000 km or 2 years

2 items

Compression test (or leak-down)

Engine

Guideline
Change gearbox oil

Primary and gearbox

Guideline

Every 19,500 km or 2 years

4 items

Replace air filter element

Fuel and air

Guideline
Synchronize throttle bodies

Fuel and air

Guideline
Clean and grease rear suspension linkage

Rear suspension and frame

Guideline
Grease swingarm pivot

Rear suspension and frame

Guideline

Every 19,500 km or 3 years

1 item

Replace CVT drive belt

Final drive

Guideline

Typical scooter interval, or sooner if the belt is cracked, glazed or below its width limit.

Every 24,000 km or 3 years

1 item

Change fork oil

Front end

Guideline

Some early telescopic forks are grease filled or use very small oil quantities. Check your manual.

Every 24,000 km

1 item

Replace brake linings / skim drums (wear based)

Brakes

Guideline

Every 25,500 km or 4 years

1 item

Replace spark plugs

Engine

Guideline

Every 32,000 km or 4 years

2 items

Repack / replace steering head bearings

Front end

Guideline

Many old machines use loose balls in cups and cones. Taper roller conversions are common.
Repack / replace wheel bearings

Wheels and tires

Guideline

Cup-and-cone and taper roller hubs need periodic repacking and adjustment.

Every 38,500 km or 4 years

1 item

Replace fuel filter

Fuel and air

Guideline

Every 40,000 km or 6 years

1 item

Replace swingarm bushes / bearings

Rear suspension and frame

Guideline

Every 48,500 km or 6 years

1 item

Rebuild forks: seals, bushes, springs

Front end

Guideline

Every 6 months

1 item

Clean battery terminals, check charge and strap

Ignition and electrics

Guideline

Every 2 years

3 items

Inspect wiring, bullet connectors and ground points

Ignition and electrics

Guideline
Inspect frame, welds and lugs for cracks

Rear suspension and frame

Guideline
Replace brake fluid

Brakes

Guideline

Every 4 years

3 items

Replace fuel lines

Fuel and air

Guideline

Old rubber and modern ethanol fuel do not mix well.
Inspect brake hoses; replace old rubber

Brakes

Guideline
Rebuild calipers and master cylinders (seals)

Brakes

Guideline

Every 6 years

1 item

Replace tires on age (regardless of tread)

Wheels and tires

Guideline

Guideline lines: Intervals here are general guidelines for the machine's era and layout, compiled for this app. They are not factory manual figures. Check your workshop manual, and edit any interval in the bike's Schedule tab.