Norge GT 8V
Library entry covers 2011-2016
Published source
Moto Guzzi Norge GT 8v Service Station Manual 897237, Maintenance chart MAIN-59
Factory workshop manual. Covers Norge GT 8v (service station manual 897237).
76 items for a 2013 model, grouped by interval the way a factory chart is laid out.
How this bike is built (what the schedule is based on)
- Engine cycle
- Four-stroke
- Engine lubrication
- Wet sump (oil in crankcase)
- Oil filtration
- Replaceable cartridge or spin-on filter
- Valve gear
- Overhead cam, screw/locknut adjusters
- Ignition
- Electronic (CDI / transistor / ECU)
- Charging
- Alternator / stator with rectifier
- Battery
- Wet cell (flooded lead-acid, needs topping up)
- Fuel system
- Fuel injection
- Cooling
- Air / oil cooled
- Primary drive
- Gear or chain inside engine, shares engine oil
- Gearbox oil
- Separate gearbox oil
- Clutch control
- Hand lever, cable
- Final drive
- Shaft
- Front suspension
- Telescopic fork
- Rear suspension
- Swingarm, twin shocks
- Front brake
- Disc, hydraulic
- Rear brake
- Disc, hydraulic
- Wheels
- Cast / alloy, tubeless
- Sidecar
- No sidecar
2013 Moto Guzzi Norge GT 8V
On the road: every 200 mi
1 item-
Check engine oil levelPre-ride / on the roadGuideline
Each fuel stop on old machines. Dry sump: check the tank hot, engine idling or just stopped, per your manual.
On the road: every 300 mi
2 items-
Check lights, horn, brake light switchesPre-ride / on the roadGuideline
-
Check tire pressuresPre-ride / on the roadGuideline
Every 1,000 mi or 6 months
1 item-
Inspect tire tread, sidewalls and date codesWheels and tiresGuideline
Every 3,000 mi or 12 months
7 items-
Check throttle cable(s) free play and returnFuel and airGuideline
-
Check steering head bearing adjustmentFront endGuideline
-
Inspect fork seals, stanchions and fork bootsFront endGuideline
-
Check footrests, pegs, rear brake and gear lever pivotsRear suspension and frameGuideline
-
Grease and check center / side stand and springsRear suspension and frameGuideline
-
Check brake pads and discsBrakesGuideline
-
Check wheel bearings for playWheels and tiresGuideline
Every 4,000 mi or 12 months
2 items-
Inspect, clean and gap spark plugsEngineGuideline
-
Adjust clutch free play, lubricate cable and lever pivotPrimary and gearboxGuideline
Every 6,000 mi or 12 months
7 items-
Clean / inspect air filterFuel and airGuideline
Mesh or oiled foam: clean and re-oil. Paper: blow out or replace. Some very early machines have no filter at all.
-
Check charging voltage and regulator / cut-outIgnition and electricsGuideline
-
Check final drive for leaks and bearing playFinal driveGuideline
-
Check swingarm bushes for playRear suspension and frameGuideline
-
Inspect rear shocks for leaks and dampingRear suspension and frameGuideline
-
Lubricate control cables and lever pivotsControls and cablesGuideline
-
Lubricate speedometer / tachometer cables, check driveControls and cablesGuideline
A dry speedo cable whips the needle and eventually kills the instrument.
Every 6,214 mi
26 items-
Bolts and nuts tighteningEngineFactory
Factory: As printed: I at 1.5, 10, 20, 30, 40, 50, 60, 70, 80 (Km x 1000)
-
Braking systemsEngineFactory
Factory: As printed: I at 1.5, 10, 20, 30, 40, 50, 60, 70, 80 (Km x 1000)
-
Change engine oilEngineFactory
Manual: Engine oil. Factory: Columns km x1000 1.5/10/20/.../80; first 1,500 km; 5,000 km if raced
-
Check and adjust valve clearancesEngineFactory
Manual: Valve clearance adjustment. Factory: First 1,500 km
-
Engine idle speedEngineFactory
Factory: As printed: A at 1.5, 10, 20, 30, 40, 50, 60, 70, 80 (Km x 1000)
-
Filter housing oil drainage pipe draining (5)EngineFactory
Factory: As printed: C at 10, 20, 30, 40, 50, 60, 70, 80 (Km x 1000); (5) Every 5000 Km if the vehicle is used for racing.
-
Light circuitEngineFactory
Factory: As printed: I at 1.5, 10, 20, 30, 40, 50, 60, 70, 80 (Km x 1000)
-
Replace oil filterEngineFactory
Manual: Engine oil filter. Factory: First 1,500 km
-
Replace spark plugsEngineFactory
Manual: Spark plugs.
-
Vehicle general operationEngineFactory
Factory: As printed: I at 1.5, 10, 20, 30, 40, 50, 60, 70, 80 (Km x 1000)
-
Carburetion at idle (CO)Fuel and airFactory
Factory: As printed: I at 10, 20, 30, 40, 50, 60, 70, 80 (Km x 1000)
-
Replace fuel linesFuel and airFactory
Manual: Fuel lines. Factory: Replace every 4 years
-
Synchronize throttle bodiesFuel and airFactory
Manual: Cylinder synchronization.
-
Change gearbox oilPrimary and gearboxFactory
Manual: Gearbox oil. Factory: First 1,500 km
-
Clutch lever pin (7)Primary and gearboxFactory
Factory: As printed: L at 1.5, 10, 20, 30, 40, 50, 60, 70, 80 (Km x 1000); note (7) is not printed with the chart
-
Clutch wearPrimary and gearboxFactory
Factory: As printed: I at 10, 20, 30, 40, 50, 60, 70, 80 (Km x 1000)
-
Replace hydraulic clutch fluidPrimary and gearboxFactory
Manual: Clutch fluid. Factory: Footnote: every 2 years or 20000 Km
-
Transmission cables and controlsPrimary and gearboxFactory
Factory: As printed: I at 1.5, 10, 20, 30, 40, 50, 60, 70, 80 (Km x 1000)
-
Change final drive (rear drive) oilFinal driveFactory
Manual: Final drive oil. Factory: First 1,500 km
-
Steering bearings and steering clearanceFront endFactory
Factory: As printed: I at 1.5, 10, 20, 30, 40, 50, 60, 70, 80 (Km x 1000)
-
Brake discsBrakesFactory
Factory: As printed: I at 1.5, 10, 20, 30, 40, 50, 60, 70, 80 (Km x 1000)
-
Brake pad wear (1)BrakesFactory
Factory: As printed: I at 1.5, 10, 20, 30, 40, 50, 60, 70, 80 (Km x 1000); (1) Check and clean and adjust or replace, if necessary, before every journey.
-
Inspect brake hoses; replace old rubberBrakesFactory
Manual: Brake lines. Factory: Replace every 4 years
-
Tires - pressure / wear (1)Wheels and tiresFactory
Factory: As printed: I at 1.5, 10, 20, 30, 40, 50, 60, 70, 80 (Km x 1000); (1) Check and clean and adjust or replace, if necessary, before every journey.
-
Wheel bearingsWheels and tiresFactory
Factory: As printed: I at 10, 20, 30, 40, 50, 60, 70, 80 (Km x 1000)
-
WheelsWheels and tiresFactory
Factory: As printed: I at 1.5, 10, 20, 30, 40, 50, 60, 70, 80 (Km x 1000)
Every 10,000 mi or 2 years
1 item-
Compression test (or leak-down)EngineGuideline
Every 12,000 mi or 2 years
1 item-
Grease swingarm pivotRear suspension and frameGuideline
Every 12,427 mi or 2 years
2 items-
Clutch fluid (2) (replace)Primary and gearboxFactory
Factory: As printed: (2) Replace every 2 years or 20000 Km (12427 mi).
-
Replace brake fluidBrakesFactory
Manual: Brake fluid. Factory: Replace every 2 years or 20000 Km (12427 mi)
Every 12,427 mi
11 items-
Alternator beltEngineFactory
Factory: Adjust at 20,000 km intervals; replace at 50,000 km
-
Exhaust pipe flange boltsEngineFactory
Factory: As printed: I at 1.5, 20, 40, 60, 80 (Km x 1000)
-
Safety switchesEngineFactory
Factory: As printed: I at 1.5, 20, 40, 60, 80 (Km x 1000)
-
Suspension and settingEngineFactory
Factory: As printed: I at 1.5, 20, 40, 60, 80 (Km x 1000)
-
Throttle bodyEngineFactory
Factory: As printed: C at 20, 40, 60, 80 (Km x 1000)
-
Air filter (I)Fuel and airFactory
Factory: As printed: I at 10, 30, 50, 70; R at 20, 40, 60, 80 (Km x 1000)
-
Replace air filter elementFuel and airFactory
Manual: Air filter. Factory: Inspect at 10,000 km intermediate services
-
Battery terminals tighteningIgnition and electricsFactory
Factory: As printed: I at 1.5, 20, 40, 60, 80 (Km x 1000)
-
Change fork oilFront endFactory
Manual: Fork oil / oil seals. Factory: Replaced at 10, 30, 50, 70 x1000 km
-
ForkFront endFactory
Factory: As printed: I at 1.5, 20, 40, 60, 80 (Km x 1000)
-
Brake fluid (2) (I)BrakesFactory
Factory: As printed: I at 1.5, 10, 30, 50, 70; R at 20, 40, 60, 80 (Km x 1000); (2) Replace every 2 years or 20000 Km (12427 mi).
Every 20,000 mi or 4 years
3 items-
Lubricate drive shaft splines / check U-jointFinal driveGuideline
-
Repack / replace steering head bearingsFront endGuideline
Many old machines use loose balls in cups and cones. Taper roller conversions are common.
-
Repack / replace wheel bearingsWheels and tiresGuideline
Cup-and-cone and taper roller hubs need periodic repacking and adjustment.
Every 24,000 mi or 4 years
1 item-
Replace fuel filterFuel and airGuideline
Every 25,000 mi or 6 years
1 item-
Replace swingarm bushes / bearingsRear suspension and frameGuideline
Every 30,000 mi or 6 years
1 item-
Rebuild forks: seals, bushes, springsFront endGuideline
Every 6 months
1 item-
Clean battery terminals, check charge and strapIgnition and electricsGuideline
Every 2 years
2 items-
Inspect wiring, bullet connectors and ground pointsIgnition and electricsGuideline
-
Inspect frame, welds and lugs for cracksRear suspension and frameGuideline
Every 4 years
3 items-
Fuel lines (3) (replace)Fuel and airFactory
Factory: As printed: (3) Replace every 4 years.
-
Brake lines (3) (replace)BrakesFactory
Factory: As printed: (3) Replace every 4 years.
-
Rebuild calipers and master cylinders (seals)BrakesGuideline
Every 6 years
1 item-
Replace tires on age (regardless of tread)Wheels and tiresGuideline
No interval set
2 items-
Alternator belt (R)EngineFactory
Factory: Printed per the re-read doubt: Alternator belt prints A at 20, 40, 60, 80 and R at 50 (Km x 1000); the R is a single mark, so no repeat interval. The existing entry holds the adjust. (From the re-read doubt notes: Moto Guzzi Norge GT 8V, printed line or second operation stated in the DOUBT line.)
-
Engine oil pressure warning light (4)EngineFactory
Factory: As printed: (4) Check at each engine start.
Guideline lines: Intervals here are general guidelines for the machine's era and layout, compiled for this app. They are not factory manual figures. Check your workshop manual, and edit any interval in the bike's Schedule tab.
Keep up with this schedule on your phone
Add the bike in the app and this chart loads itself, ready to log against and edit.
