No photo of this model in the library yet.

Have this bike? Send a photo or the manual's service chart

Royal Enfield · Overhead-cam four-stroke single, wet sump, gearbox shares engine oil, chain drive

Classic 350

Library entry covers 2010-2024

42 factory 40 guideline

Published source

Royal Enfield Classic 350 Owner's Manual (USA), Periodic Maintenance Chart

Factory owner's handbook. Covers Classic 350 J-series (2021 on), USA manual Part No. RAM00359/B, 8 May 2025; earlier UCE years not covered.

82 items for a 2014 model, grouped by interval the way a factory chart is laid out.

How this bike is built (what the schedule is based on)

Engine cycle: Four-stroke
Engine lubrication: Wet sump (oil in crankcase)
Oil filtration: Replaceable cartridge or spin-on filter
Valve gear: Overhead cam, screw/locknut adjusters
Ignition: Electronic (CDI / transistor / ECU)
Charging: Alternator / stator with rectifier
Battery: Wet cell (flooded lead-acid, needs topping up)
Fuel system: Single carburetor
Cooling: Air / oil cooled
Primary drive: Gear or chain inside engine, shares engine oil
Gearbox oil: Shares engine oil
Clutch control: Hand lever, cable
Final drive: Chain
Front suspension: Telescopic fork
Rear suspension: Swingarm, twin shocks
Front brake: Disc, hydraulic
Rear brake: Drum (or band / belt rim)
Wheels: Spoked, tubed
Sidecar: No sidecar

Maintenance schedule

2014 Royal Enfield Classic 350

On the road: every 200 mi

1 item

Check engine oil level

Pre-ride / on the road

Guideline

Each fuel stop on old machines. Dry sump: check the tank hot, engine idling or just stopped, per your manual.

On the road: every 300 mi

3 items

Check lights, horn, brake light switches

Pre-ride / on the road

Guideline
Check tire pressures

Pre-ride / on the road

Guideline
Lubricate drive chain

Pre-ride / on the road

Guideline

Lube warm, ideally at the end of the riding day so it soaks in overnight. Sooner after rain.

On the road: every 600 mi

1 item

Check chain slack and rear wheel alignment

Pre-ride / on the road

Guideline

Every 621 mi

3 items

Clutch lever / cable free play: adjust

Primary and gearbox

Factory

Factory: As printed: every 1,000 km or earlier as required (no marks)
Rear wheel drive chain: clean and lubricate

Final drive

Factory

Factory: As printed: every 1,000 km (no marks)
Hand levers & foot levers: lubricate

Controls and cables

Factory

Factory: As printed: every 1,000 km or earlier as required (no marks)

Every 1,000 mi or 6 months

1 item

Adjust rear drum brake and rod / cable linkage

Brakes

Guideline

Every 3,000 mi or 6 months

16 items

All mounting fasteners in vehicle for tightness: I

Engine

Factory

Factory: As printed: mark in all 11 columns (0.5, 5, 10 ... 50 x1000 km)
Evaporative emission equipment rubber hoses & drain the overfilled by removing plug: I

Engine

Factory

Factory: As printed: mark in all 11 columns (0.5, 5, 10 ... 50 x1000 km); I at all columns except R at 40
HT lead for crack: I

Engine

Factory

Factory: As printed: mark in all 11 columns (0.5, 5, 10 ... 50 x1000 km)
Injector hose: I

Engine

Factory

Factory: As printed: mark in all 11 columns (0.5, 5, 10 ... 50 x1000 km)
Rubber hose-intake adapter: I

Engine

Factory

Factory: As printed: mark in all 11 columns (0.5, 5, 10 ... 50 x1000 km)
Starter motor & starter relay connection: I

Engine

Factory

Factory: As printed: mark in all 11 columns (0.5, 5, 10 ... 50 x1000 km)
Clean / inspect air filter

Fuel and air

Factory

Manual: Air filter element. Factory: Clean at 5,000 km columns between replacements; more often if dusty.
Vent pipe under air filter box: I

Fuel and air

Factory

Factory: As printed: mark in all 11 columns (0.5, 5, 10 ... 50 x1000 km)
Clean battery terminals, check charge and strap

Ignition and electrics

Factory

Manual: Battery terminals (apply petroleum jelly). Factory: Clean every column.
Front fork oil (I)

Front end

Factory

Factory: Printed per the re-read doubt: the Front fork oil row prints I at all columns except R at 20 and 40 x1000 km; columns are 0.5/0.3/1.5 then 5/3/6 steps (km x1000 / mi x1000 / months), taken as inspect every 5,000 km / 3,000 mi / 6 months. The existing entry holds the R operation. (From the re-read doubt notes: Royal Enfield Classic 350, printed line or second operation stated in the DOUBT line.)
Check footrests, pegs, rear brake and gear lever pivots

Rear suspension and frame

Factory

Manual: Pivot points (side stand, gear shifter, brake pedal, levers). Factory: Lubricate every column.
Grease and check center / side stand and springs

Rear suspension and frame

Factory

Manual: Pivot points (side stand, center stand). Factory: Lubricate every column.
Side stand switch operation: I

Rear suspension and frame

Factory

Factory: As printed: mark in all 11 columns (0.5, 5, 10 ... 50 x1000 km)
Check brake pads and discs

Brakes

Factory

Manual: Brake pads. Factory: Inspect every column.
Inspect brake hoses; replace old rubber

Brakes

Factory

Manual: Brake hoses and banjo bolts. Factory: Inspect every column.
Inspect tire tread, sidewalls and date codes

Wheels and tires

Factory

Manual: Tire wear pattern. Factory: Inspect every column, whichever is earlier.

Every 3,000 mi or 12 months

8 items

Check throttle cable(s) free play and return

Fuel and air

Guideline
Clean fuel tap filter / sediment bowl

Fuel and air

Guideline
Clean drive chain thoroughly (remove and soak, re-lube)

Final drive

Guideline

Non O-ring chains on old machines: remove, clean, soak in hot chain grease or lube, refit with the master link clip closed end leading.
Inspect chain and sprockets for wear (measure stretch)

Final drive

Guideline
Check steering head bearing adjustment

Front end

Guideline
Inspect fork seals, stanchions and fork boots

Front end

Guideline
Check spoke tension and wheel true

Wheels and tires

Guideline
Check wheel bearings for play

Wheels and tires

Guideline

Every 3,107 mi

4 items

Rear wheel drive chain: clean, lubricate and adjust

Final drive

Factory

Factory: As printed: every 5,000 km or earlier as required (no marks)
Steering ball races play: inspect & adjust, lubricate if required

Front end

Factory

Factory: As printed: every 5,000 km or earlier (no marks)
Swing arm pivot bush & spacer: inspect, lubricate if required

Rear suspension and frame

Factory

Factory: As printed: every 5,000 km or earlier (1 I mark, column not readable)
Throttle cable: adjust

Controls and cables

Factory

Factory: As printed: every 5,000 km or earlier if required (no marks)

Every 4,000 mi or 12 months

3 items

Inspect, clean and gap spark plugs

Engine

Guideline
Adjust clutch free play, lubricate cable and lever pivot

Primary and gearbox

Guideline
Lubricate brake cam spindles, check linings and drums

Brakes

Guideline

Every 5,000 mi or 12 months

1 item

Replace oil filter

Engine

Guideline

Every 6,000 mi or 12 months

13 items

Change engine oil

Engine

Factory

Manual: Engine oil level / replace. Factory: R at 500 km then every 10,000 km / 6,000 mi / 12 months; inspect between.
Engine oil filter element (replace)

Engine

Factory

Factory: R at 500 km, then every 10000 km (6000 mi) / 12 months Re-read from Royal Enfield Classic 350 owner's manual (USA) pages 114-118, periodical maintenance chart
Engine oil strainer on crankcase LH (clean)

Engine

Factory

Factory: C at 500 km, then every 10000 km (6000 mi) / 12 months Re-read from Royal Enfield Classic 350 owner's manual (USA) pages 114-118, periodical maintenance chart
Inlet/exhaust tappet setting (inspect and adjust)

Engine

Factory

Factory: I&A every 10000 km (6000 mi) / 12 months Re-read from Royal Enfield Classic 350 owner's manual (USA) pages 114-118, periodical maintenance chart
Spark plug (clean and adjust)

Engine

Factory

Factory: C&A at 10000, 30000, 50000 km; replaced at 20000 and 40000 km Re-read from Royal Enfield Classic 350 owner's manual (USA) pages 114-118, periodical maintenance chart
Clean carburetor float bowl(s), check float level and jets

Fuel and air

Guideline

Ethanol fuel varnishes old carbs quickly in storage.
Replace air filter element

Fuel and air

Factory

Manual: Air filter element. Factory: R at 10,000 km / 6,000 mi / 12 month columns.
Check charging voltage and regulator / cut-out

Ignition and electrics

Guideline
Check swingarm bushes for play

Rear suspension and frame

Guideline
Inspect rear shocks for leaks and damping

Rear suspension and frame

Guideline
Spokes tightness / wheel rim run out, front and rear (inspect)

Wheels and tires

Factory

Factory: I at 500 km, then every 10000 km (6000 mi) / 12 months Re-read from Royal Enfield Classic 350 owner's manual (USA) pages 114-118, periodical maintenance chart
Lubricate control cables and lever pivots

Controls and cables

Guideline
Lubricate speedometer / tachometer cables, check drive

Controls and cables

Guideline

A dry speedo cable whips the needle and eventually kills the instrument.

Every 6,214 mi or 12 months

1 item

Throttle body, cleaning

Engine

Factory

Factory: As printed: every 10,000 km / 12 months or earlier as required (no marks); remove the throttle body and clean with a dry microfiber cloth; throttle body cleaners, solvents and alcohol-based liquids are prohibited

Every 8,000 mi or 2 years

1 item

Check and adjust valve clearances

Engine

Guideline

Every 10,000 mi or 2 years

1 item

Compression test (or leak-down)

Engine

Guideline

Every 12,000 mi or 2 years

6 items

Spark plug (replace)

Engine

Factory

Factory: R at 20000 and 40000 km (12000, 24000 mi) Re-read from Royal Enfield Classic 350 owner's manual (USA) pages 114-118, periodical maintenance chart
Change fork oil

Front end

Factory

Manual: Front fork oil. Factory: R at 20,000 km / 12,000 mi / 24 months and 40,000 km; inspect elsewhere.
Grease swingarm pivot

Rear suspension and frame

Guideline
Brake fluid level, front & rear disc: R

Brakes

Factory

Factory: As printed: R at 20 and 40 x1000 km (12 and 24 x1000 mi, 24 and 48 months) columns
Replace brake fluid

Brakes

Factory

Manual: Brake fluid level. Factory: R at 20,000 km and 40,000 km columns; inspect elsewhere.
Rear wheel cush drive rubbers (inspect and replace)

Wheels and tires

Factory

Factory: I&R at 20000 and 40000 km (12000, 24000 mi) Re-read from Royal Enfield Classic 350 owner's manual (USA) pages 114-118, periodical maintenance chart

Every 15,000 mi

1 item

Replace brake linings / skim drums (wear based)

Brakes

Guideline

Every 16,000 mi or 4 years

1 item

Replace spark plugs

Engine

Guideline

Every 18,000 mi or 3 years

2 items

Fuel filter in fuel pump (replace)

Fuel and air

Factory

Factory: R at 30000 km (18000 mi) / 36 months Re-read from Royal Enfield Classic 350 owner's manual (USA) pages 114-118, periodical maintenance chart
Earth wire eyelet contact (inspect)

Ignition and electrics

Factory

Factory: Marked at 20000 km (12000 mi, 24 months) and 50000 km (30000 mi, 60 months) Re-read from Royal Enfield Classic 350 owner's manual (USA) pages 114-118, periodical maintenance chart

Every 18,000 mi

1 item

Replace chain and sprockets (wear based)

Final drive

Guideline

Every 20,000 mi or 4 years

2 items

Repack / replace steering head bearings

Front end

Guideline

Many old machines use loose balls in cups and cones. Taper roller conversions are common.
Repack / replace wheel bearings

Wheels and tires

Guideline

Cup-and-cone and taper roller hubs need periodic repacking and adjustment.

Every 24,000 mi or 4 years

1 item

Evaporative emission equipment rubber hoses: R

Engine

Factory

Factory: As printed: R at 40 x1000 km (24 x1000 mi, 48 months) column

Every 25,000 mi or 6 years

1 item

Replace swingarm bushes / bearings

Rear suspension and frame

Guideline

Every 30,000 mi or 6 years

1 item

Rebuild forks: seals, bushes, springs

Front end

Guideline

Every 2 years

2 items

Inspect wiring, bullet connectors and ground points

Ignition and electrics

Guideline
Inspect frame, welds and lugs for cracks

Rear suspension and frame

Guideline

Every 4 years

2 items

Replace fuel lines

Fuel and air

Guideline

Old rubber and modern ethanol fuel do not mix well.
Rebuild calipers and master cylinders (seals)

Brakes

Guideline

Every 6 years

2 items

Replace inner tubes and rim tape with tires

Wheels and tires

Guideline
Replace tires on age (regardless of tread)

Wheels and tires

Guideline

No interval set

3 items

Clutch lever / cable free play: replace if required

Primary and gearbox

Factory

Factory: As printed: replace if required
Steering ball races play: replace if necessary

Front end

Factory

Factory: As printed: replace if necessary
Swing arm pivot bush & spacer: replace if necessary

Rear suspension and frame

Factory

Factory: As printed: replace if necessary

Guideline lines: Intervals here are general guidelines for the machine's era and layout, compiled for this app. They are not factory manual figures. Check your workshop manual, and edit any interval in the bike's Schedule tab.