MotoService Log
No photo of this model in the library yet.

Have this bike? Send a photo or the manual's service chart

Seat · Overhead-cam four-stroke single, wet sump, gearbox shares engine oil, chain drive

MO 125

Library entry covers 2021-2024

13 factory 46 guideline

Published source

SEAT MÓ eScooter owner's manual (multilingual, English section), maintenance pp.37-41 incl. Operations and frequency table p.38 and Inspection work p.41; filed by SEAT Austria as 'Benutzerhandbuch SEAT MÓ 125 2022'

Factory owner's handbook. Covers eScooter SEAT MÓ (production plate TYPE: S01A, p.42); multilingual owner's manual filed on seat.at as benutzerhandbuch-seat-m(o)-125-2022; no print year or edition in the document.

59 items for a 2021 model, grouped by interval the way a factory chart is laid out.

How this bike is built (what the schedule is based on)
Engine cycle
Four-stroke
Engine lubrication
Wet sump (oil in crankcase)
Oil filtration
Replaceable cartridge or spin-on filter
Valve gear
Overhead cam, screw/locknut adjusters
Ignition
Electronic (CDI / transistor / ECU)
Charging
Alternator / stator with rectifier
Battery
Wet cell (flooded lead-acid, needs topping up)
Fuel system
Fuel injection
Cooling
Air / oil cooled
Primary drive
Gear or chain inside engine, shares engine oil
Gearbox oil
Shares engine oil
Clutch control
Automatic or semi-automatic
Final drive
Chain
Front suspension
Telescopic fork
Rear suspension
Swingarm, single shock / cantilever
Front brake
Disc, hydraulic
Rear brake
Disc, hydraulic
Wheels
Spoked, tubed
Sidecar
No sidecar
Maintenance schedule

2021 Seat MO 125

On the road: every 300 km

1 item
  • Check engine oil level
    Pre-ride / on the road
    Guideline

    Each fuel stop on old machines. Dry sump: check the tank hot, engine idling or just stopped, per your manual.

On the road: every 500 km

3 items
  • Check lights, horn, brake light switches
    Pre-ride / on the road
    Guideline
  • Check tire pressures
    Pre-ride / on the road
    Guideline
  • Lubricate drive chain
    Pre-ride / on the road
    Guideline

    Lube warm, ideally at the end of the riding day so it soaks in overnight. Sooner after rain.

On the road: every 1,000 km

1 item
  • Check chain slack and rear wheel alignment
    Pre-ride / on the road
    Guideline

Every 5,000 km or 12 months

11 items
  • Periodic service inspection (dealer; work per SEAT maintenance plan)
    Engine
    Factory

    Factory: p.41 Inspection work, as printed: 'first service at 1,000 miles (1,500 km) or 3 months', 'second service at 3,000 miles (5,000 km)', 'third at 6,000 miles (10,000 km)', 'and the next services every 3,000 miles (5,000 km).' p.41: inspected 'at least once a year', 'the first being carried out 3 months after purchase'; p.16-17: 'Regardless of the kilometers travelled, the eScooter must pass at least one revision each year'. p.41 says what to inspect is in the corresponding manual/maintenance plans (not in this owner's manual).

  • Check throttle cable(s) free play and return
    Fuel and air
    Guideline
  • Adjust automatic / semi-automatic clutch
    Primary and gearbox
    Guideline
  • Clean drive chain thoroughly (remove and soak, re-lube)
    Final drive
    Guideline

    Non O-ring chains on old machines: remove, clean, soak in hot chain grease or lube, refit with the master link clip closed end leading.

  • Inspect chain and sprockets for wear (measure stretch)
    Final drive
    Guideline
  • Check steering head bearing adjustment
    Front end
    Guideline
  • Inspect fork seals, stanchions and fork boots
    Front end
    Guideline
  • Check footrests, pegs, rear brake and gear lever pivots
    Rear suspension and frame
    Guideline
  • Grease and check center / side stand and springs
    Rear suspension and frame
    Guideline
  • Check spoke tension and wheel true
    Wheels and tires
    Guideline
  • Check wheel bearings for play
    Wheels and tires
    Guideline

Every 6,500 km or 12 months

1 item
  • Inspect, clean and gap spark plugs
    Engine
    Guideline

Every 8,000 km or 12 months

2 items
  • Change engine oil
    Engine
    Guideline

    Pre-1970 machines: many owners run non-detergent or classic-spec oil with no filter, so short intervals matter. Dry sump: drain the tank and the crankcase/sump, flush the tank and clean the feed and return screens.

  • Replace oil filter
    Engine
    Guideline

Every 9,500 km or 12 months

6 items
  • Clean / inspect air filter
    Fuel and air
    Guideline

    Mesh or oiled foam: clean and re-oil. Paper: blow out or replace. Some very early machines have no filter at all.

  • Check charging voltage and regulator / cut-out
    Ignition and electrics
    Guideline
  • Check swingarm bushes for play
    Rear suspension and frame
    Guideline
  • Inspect rear shocks for leaks and damping
    Rear suspension and frame
    Guideline
  • Lubricate control cables and lever pivots
    Controls and cables
    Guideline
  • Lubricate speedometer / tachometer cables, check drive
    Controls and cables
    Guideline

    A dry speedo cable whips the needle and eventually kills the instrument.

Every 13,000 km or 2 years

1 item
  • Check and adjust valve clearances
    Engine
    Guideline

Every 16,000 km or 2 years

1 item
  • Compression test (or leak-down)
    Engine
    Guideline

Every 19,500 km or 2 years

4 items
  • Replace air filter element
    Fuel and air
    Guideline
  • Synchronize throttle bodies
    Fuel and air
    Guideline
  • Clean and grease rear suspension linkage
    Rear suspension and frame
    Guideline
  • Grease swingarm pivot
    Rear suspension and frame
    Guideline

Every 24,000 km or 3 years

1 item
  • Change fork oil
    Front end
    Guideline

    Some early telescopic forks are grease filled or use very small oil quantities. Check your manual.

Every 25,500 km or 4 years

1 item
  • Replace spark plugs
    Engine
    Guideline

Every 29,000 km

1 item
  • Replace chain and sprockets (wear based)
    Final drive
    Guideline

Every 32,000 km or 4 years

2 items
  • Repack / replace steering head bearings
    Front end
    Guideline

    Many old machines use loose balls in cups and cones. Taper roller conversions are common.

  • Repack / replace wheel bearings
    Wheels and tires
    Guideline

    Cup-and-cone and taper roller hubs need periodic repacking and adjustment.

Every 38,500 km or 4 years

1 item
  • Replace fuel filter
    Fuel and air
    Guideline

Every 40,000 km or 6 years

1 item
  • Replace swingarm bushes / bearings
    Rear suspension and frame
    Guideline

Every 48,500 km or 6 years

1 item
  • Rebuild forks: seals, bushes, springs
    Front end
    Guideline

Every 1 month

4 items
  • Metal parts (clean and grease with oil)
    Engine
    Factory

    Factory: p.38 Operations and frequency table: Monthly.

  • Painted parts (clean with a shine restorer)
    Engine
    Factory

    Factory: p.38 Operations and frequency table: Monthly.

  • Rubber parts (clean with rubber protection products)
    Engine
    Factory

    Factory: p.38 Operations and frequency table: Monthly.

  • Battery (charge fully)
    Ignition and electrics
    Factory

    Factory: p.34 and p.41, as printed: 'The battery must be charged completely once every 30 days to keep the warranty valid.' p.34: full charge to 100% 'at least once a month'. p.41: fully charge before parking for more than one week.

Every 6 months

1 item
  • Clean battery terminals, check charge and strap
    Ignition and electrics
    Guideline

Every 2 years

3 items
  • Inspect wiring, bullet connectors and ground points
    Ignition and electrics
    Guideline
  • Inspect frame, welds and lugs for cracks
    Rear suspension and frame
    Guideline
  • Replace brake fluid
    Brakes
    Factory

    Manual: Brake fluid (change). Factory: p.11, as printed: 'the fluid must be changed every 2 years'.

Every 4 years

3 items
  • Replace fuel lines
    Fuel and air
    Guideline

    Old rubber and modern ethanol fuel do not mix well.

  • Inspect brake hoses; replace old rubber
    Brakes
    Guideline
  • Rebuild calipers and master cylinders (seals)
    Brakes
    Guideline

Every 6 years

2 items
  • Replace inner tubes and rim tape with tires
    Wheels and tires
    Guideline
  • Replace tires on age (regardless of tread)
    Wheels and tires
    Guideline

No interval set

7 items
  • Aluminium parts (apply rust-protective spray; remove rust with steel wool and soap)
    Engine
    Factory

    Factory: p.38 Operations and frequency table: Weekly.

  • Instrument panel (remove hardened dirt with a soft sponge)
    Engine
    Factory

    Factory: p.38 Operations and frequency table: As needed.

  • Lights (remove hardened dirt with a soft sponge)
    Engine
    Factory

    Factory: p.38 Operations and frequency table: As needed.

  • Screen (wipe with a soft sponge)
    Engine
    Factory

    Factory: p.38 Operations and frequency table: Every day used.

  • Saddle (wipe with a soft sponge)
    Rear suspension and frame
    Factory

    Factory: p.38 Operations and frequency table: Every day used.

  • Check brake pads and discs
    Brakes
    Factory

    Manual: Rear brake pads (replace). Factory: p.11: replace when less than 1 mm thick (wear limit, no interval).

  • Inspect tire tread, sidewalls and date codes
    Wheels and tires
    Factory

    Manual: Tires (check pressure matches specifications, p.43). Factory: p.38 Operations and frequency table: Weekly.

Guideline lines: Intervals here are general guidelines for the machine's era and layout, compiled for this app. They are not factory manual figures. Check your workshop manual, and edit any interval in the bike's Schedule tab.

Keep up with this schedule on your phone

Add the bike in the app and this chart loads itself, ready to log against and edit.

Coming soon to Google Play