No photo of this model in the library yet.

Have this bike? Send a photo or the manual's service chart

SWM · Shim-adjusted overhead-cam four-stroke, wet sump, gearbox shares engine oil, chain drive

SuperDual

Library entry covers 2016-2025

39 factory 52 guideline

Published source

SWM Superdual E4 2017 manual, scheduled maintenance chart pp.A-2, A-3, A-6, A-7 (ManualsLib viewer pp.316-321)

Factory owner's handbook. Covers SWM Superdual E4 2017 use and maintenance manual (IT/EN/FR/DE/ES); other years not compared.

91 items for a 2023 model, grouped by interval the way a factory chart is laid out.

How this bike is built (what the schedule is based on)

Engine cycle: Four-stroke
Engine lubrication: Wet sump (oil in crankcase)
Oil filtration: Replaceable cartridge or spin-on filter
Valve gear: Overhead cam, shim adjusted (incl. desmo)
Ignition: Electronic (CDI / transistor / ECU)
Charging: Alternator / stator with rectifier
Battery: Wet cell (flooded lead-acid, needs topping up)
Fuel system: Fuel injection
Cooling: Liquid cooled
Primary drive: Gear or chain inside engine, shares engine oil
Gearbox oil: Shares engine oil
Clutch control: Hand lever, hydraulic
Final drive: Chain
Front suspension: Telescopic fork
Rear suspension: Swingarm, single shock / cantilever
Front brake: Disc, hydraulic
Rear brake: Disc, hydraulic
Wheels: Spoked, tubed
Sidecar: No sidecar

Maintenance schedule

2023 SWM SuperDual

On the road: every 300 km

1 item

Check engine oil level

Pre-ride / on the road

Guideline

Each fuel stop on old machines. Dry sump: check the tank hot, engine idling or just stopped, per your manual.

On the road: every 500 km

3 items

Check lights, horn, brake light switches

Pre-ride / on the road

Guideline
Check tire pressures

Pre-ride / on the road

Guideline
Lubricate drive chain

Pre-ride / on the road

Guideline

Lube warm, ideally at the end of the riding day so it soaks in overnight. Sooner after rain.

On the road: every 800 km

1 item

Check coolant level

Pre-ride / on the road

Guideline

On the road: every 1,000 km

1 item

Check chain slack and rear wheel alignment

Pre-ride / on the road

Guideline

Every 1,000 km

1 item

Headlamp beam height (check)

Engine

Factory

Factory: Scheduled maintenance chart (p.A-6): C at 1,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.

Every 1,600 km or 6 months

1 item

Inspect tire tread, sidewalls and date codes

Wheels and tires

Guideline

Every 5,000 km or 12 months

10 items

Check throttle cable(s) free play and return

Fuel and air

Guideline
Clean drive chain thoroughly (remove and soak, re-lube)

Final drive

Guideline

Non O-ring chains on old machines: remove, clean, soak in hot chain grease or lube, refit with the master link clip closed end leading.
Inspect chain and sprockets for wear (measure stretch)

Final drive

Guideline
Check steering head bearing adjustment

Front end

Guideline
Inspect fork seals, stanchions and fork boots

Front end

Guideline
Check footrests, pegs, rear brake and gear lever pivots

Rear suspension and frame

Guideline
Grease and check center / side stand and springs

Rear suspension and frame

Guideline
Check brake pads and discs

Brakes

Guideline
Check spoke tension and wheel true

Wheels and tires

Guideline
Check wheel bearings for play

Wheels and tires

Guideline

Every 5,000 km

20 items

Electric fan (check)

Engine

Factory

Factory: Scheduled maintenance chart (p.A-6): C at 1,000, 10,000, 15,000 and 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Engine oil (change)

Engine

Factory

Factory: Scheduled maintenance chart (p.A-2): S at 1,000, 5,000, 10,000, 15,000 and 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Lights, indicators and horn (check)

Engine

Factory

Factory: Scheduled maintenance chart (p.A-6): C at 1,000, 5,000, 10,000, 15,000 and 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Lubrication and greasing

Engine

Factory

Factory: Scheduled maintenance chart (p.A-7): L at 1,000, 5,000, 10,000, 15,000 and 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Overall tightening of nuts and bolts

Engine

Factory

Factory: Scheduled maintenance chart (p.A-7): C at 1,000, 5,000, 10,000, 15,000 and 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Spark plug cap (check)

Engine

Factory

Factory: Scheduled maintenance chart (p.A-2): C at 5,000, 10,000, 15,000 and 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Throttle (check)

Engine

Factory

Factory: Scheduled maintenance chart (p.A-6): C at 1,000, 5,000, 10,000, 15,000 and 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Valve clearance (check)

Engine

Factory

Factory: Scheduled maintenance chart (p.A-2): C (*) at 1,000, 5,000, 10,000, 15,000 and 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Air filter (clean or change)

Fuel and air

Factory

Factory: Scheduled maintenance chart (p.A-3): P at 1,000 km; P/S at 5,000 and 15,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Battery (check)

Ignition and electrics

Factory

Factory: Scheduled maintenance chart (p.A-6): C at 5,000, 10,000, 15,000 and 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Gearbox output sprocket and rear sprocket (check)

Primary and gearbox

Factory

Factory: Scheduled maintenance chart (p.A-7): C at 5,000 and 15,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Chain (check, lubricate)

Final drive

Factory

Factory: Scheduled maintenance chart (p.A-7): CL at 1,000, 5,000 and 15,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Secondary drive chain and chain tensioner rollers (check, lubricate)

Final drive

Factory

Factory: Scheduled maintenance chart (p.A-7): CL at 1,000, 5,000 and 15,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Steering bearing play (check)

Front end

Factory

Factory: Scheduled maintenance chart (p.A-6): C at 1,000, 10,000, 15,000 and 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Side stand screws (check)

Rear suspension and frame

Factory

Factory: Scheduled maintenance chart (p.A-7): C at 1,000, 5,000, 10,000, 15,000 and 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Brake hydraulic controls (check)

Brakes

Factory

Factory: Scheduled maintenance chart (p.A-6): C at 1,000, 5,000, 10,000, 15,000 and 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Clutch and brake fluids (check)

Brakes

Factory

Factory: Scheduled maintenance chart (p.A-6): C at 1,000, 5,000 and 15,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Tire pressure and wear (check)

Wheels and tires

Factory

Factory: Scheduled maintenance chart (p.A-6): C at 1,000, 5,000, 10,000, 15,000 and 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Wheel spoke tension (check)

Wheels and tires

Factory

Factory: Scheduled maintenance chart (p.A-6): C at 1,000, 5,000, 10,000, 15,000 and 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Bowden cables (clean)

Controls and cables

Factory

Factory: Scheduled maintenance chart (p.A-6): C at 1,000 km; P at 5,000, 10,000, 15,000 and 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.

Every 6,500 km or 12 months

1 item

Inspect, clean and gap spark plugs

Engine

Guideline

Every 8,000 km or 12 months

2 items

Change engine oil

Engine

Guideline

Pre-1970 machines: many owners run non-detergent or classic-spec oil with no filter, so short intervals matter. Dry sump: drain the tank and the crankcase/sump, flush the tank and clean the feed and return screens.
Replace oil filter

Engine

Guideline

Every 9,500 km or 12 months

7 items

Inspect coolant hoses and clamps

Engine

Guideline
Clean / inspect air filter

Fuel and air

Guideline

Mesh or oiled foam: clean and re-oil. Paper: blow out or replace. Some very early machines have no filter at all.
Check charging voltage and regulator / cut-out

Ignition and electrics

Guideline
Check swingarm bushes for play

Rear suspension and frame

Guideline
Inspect rear shocks for leaks and damping

Rear suspension and frame

Guideline
Lubricate control cables and lever pivots

Controls and cables

Guideline
Lubricate speedometer / tachometer cables, check drive

Controls and cables

Guideline

A dry speedo cable whips the needle and eventually kills the instrument.

Every 10,000 km

14 items

Engine oil filter cartridge (change)

Engine

Factory

Factory: Scheduled maintenance chart (p.A-2): S at 1,000, 10,000 and 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Engine oil intake filter (clean)

Engine

Factory

Factory: Scheduled maintenance chart (p.A-2): P at 1,000, 10,000 and 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Intake and exhaust rocker arms (check)

Engine

Factory

Factory: Scheduled maintenance chart (p.A-2): C at 10,000 and 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Spark plug (check)

Engine

Factory

Factory: Scheduled maintenance chart (p.A-2): C at 5,000 and 15,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Spark plug (replace)

Engine

Factory

Factory: Scheduled maintenance chart (p.A-2): S at 10,000 and 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Air filter (change)

Fuel and air

Factory

Factory: Scheduled maintenance chart (p.A-3): S at 10,000 and 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Clutch cush drive damper (check)

Primary and gearbox

Factory

Factory: Scheduled maintenance chart (p.A-3): C at 10,000 and 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Gearbox output sprocket and rear sprocket (change)

Primary and gearbox

Factory

Factory: Scheduled maintenance chart (p.A-7): S at 10,000 and 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Chain (change)

Final drive

Factory

Factory: Scheduled maintenance chart (p.A-7): S at 10,000 and 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Secondary drive chain and chain tensioner rollers (change)

Final drive

Factory

Factory: Scheduled maintenance chart (p.A-7): S at 10,000 and 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Front fork fluid (change, fork overhaul)

Front end

Factory

Factory: Scheduled maintenance chart (p.A-7): S/R at 10,000 and 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Brake pad wear (check)

Brakes

Factory

Factory: Scheduled maintenance chart (p.A-6): C at 1,000 and 10,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Clutch and brake fluids (change)

Brakes

Factory

Factory: Scheduled maintenance chart (p.A-6): S at 10,000 and 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Wheel hub bearings (check)

Wheels and tires

Factory

Factory: Scheduled maintenance chart (p.A-7): C at 10,000 and 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.

Every 16,000 km or 2 years

1 item

Compression test (or leak-down)

Engine

Guideline

Every 19,500 km or 2 years

4 items

Replace air filter element

Fuel and air

Guideline
Synchronize throttle bodies

Fuel and air

Guideline
Clean and grease rear suspension linkage

Rear suspension and frame

Guideline
Grease swingarm pivot

Rear suspension and frame

Guideline

Every 20,000 km

4 items

Timing driven gear (replace)

Ignition and electrics

Factory

Factory: Scheduled maintenance chart (p.A-2): S at 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Timing chain (replace)

Final drive

Factory

Factory: Scheduled maintenance chart (p.A-2): S at 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Timing chain slider (replace)

Final drive

Factory

Factory: Scheduled maintenance chart (p.A-2): S at 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.
Brake pads (change)

Brakes

Factory

Factory: Scheduled maintenance chart (p.A-6): S at 20,000 km. Columns: 1,000, 5,000, 10,000, 15,000 and 20,000 km; work to be done at an SWM dealer. Codes: C = check; C (*) = check clearance; L = lubricate; P = clean; P/S = clean or change depending on use; R = front fork overhaul; S = change; CL as printed in the chain rows.

Every 24,000 km or 3 years

1 item

Change fork oil

Front end

Guideline

Some early telescopic forks are grease filled or use very small oil quantities. Check your manual.

Every 24,000 km or 4 years

1 item

Check valve clearances (shim adjusted)

Engine

Guideline

Every 25,500 km or 4 years

1 item

Replace spark plugs

Engine

Guideline

Every 29,000 km

1 item

Replace chain and sprockets (wear based)

Final drive

Guideline

Every 32,000 km or 4 years

2 items

Repack / replace steering head bearings

Front end

Guideline

Many old machines use loose balls in cups and cones. Taper roller conversions are common.
Repack / replace wheel bearings

Wheels and tires

Guideline

Cup-and-cone and taper roller hubs need periodic repacking and adjustment.

Every 38,500 km or 4 years

1 item

Replace fuel filter

Fuel and air

Guideline

Every 40,000 km or 6 years

1 item

Replace swingarm bushes / bearings

Rear suspension and frame

Guideline

Every 48,500 km or 6 years

1 item

Rebuild forks: seals, bushes, springs

Front end

Guideline

Every 6 months

1 item

Clean battery terminals, check charge and strap

Ignition and electrics

Guideline

Every 2 years

5 items

Replace coolant

Engine

Guideline
Inspect wiring, bullet connectors and ground points

Ignition and electrics

Guideline
Replace hydraulic clutch fluid

Primary and gearbox

Guideline
Inspect frame, welds and lugs for cracks

Rear suspension and frame

Guideline
Replace brake fluid

Brakes

Guideline

Every 4 years

3 items

Replace fuel lines

Fuel and air

Guideline

Old rubber and modern ethanol fuel do not mix well.
Inspect brake hoses; replace old rubber

Brakes

Guideline
Rebuild calipers and master cylinders (seals)

Brakes

Guideline

Every 6 years

2 items

Replace inner tubes and rim tape with tires

Wheels and tires

Guideline
Replace tires on age (regardless of tread)

Wheels and tires

Guideline

Guideline lines: Intervals here are general guidelines for the machine's era and layout, compiled for this app. They are not factory manual figures. Check your workshop manual, and edit any interval in the bike's Schedule tab.