MotoService Log
No photo of this model in the library yet.

Have this bike? Send a photo or the manual's service chart

Husqvarna · Shim-adjusted overhead-cam four-stroke, wet sump, gearbox shares engine oil, chain drive

TXC 250

Library entry covers 2008-2013

57 factory 52 guideline

Published source

Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, ManualsLib

Factory owner's handbook. Covers edition 2013 (USA).

109 items for a 2008 model, grouped by interval the way a factory chart is laid out.

How this bike is built (what the schedule is based on)
Engine cycle
Four-stroke
Engine lubrication
Wet sump (oil in crankcase)
Oil filtration
Replaceable cartridge or spin-on filter
Valve gear
Overhead cam, shim adjusted (incl. desmo)
Ignition
Electronic (CDI / transistor / ECU)
Charging
Alternator / stator with rectifier
Battery
Wet cell (flooded lead-acid, needs topping up)
Fuel system
Fuel injection
Cooling
Liquid cooled
Primary drive
Gear or chain inside engine, shares engine oil
Gearbox oil
Shares engine oil
Clutch control
Hand lever, hydraulic
Final drive
Chain
Front suspension
Telescopic fork
Rear suspension
Swingarm, single shock / cantilever
Front brake
Disc, hydraulic
Rear brake
Disc, hydraulic
Wheels
Spoked, tubed
Sidecar
No sidecar
Maintenance schedule

2008 Husqvarna TXC 250

On the road: every 300 km

1 item
  • Check engine oil level
    Pre-ride / on the road
    Guideline

    Each fuel stop on old machines. Dry sump: check the tank hot, engine idling or just stopped, per your manual.

On the road: every 500 km

3 items
  • Check lights, horn, brake light switches
    Pre-ride / on the road
    Guideline
  • Check tire pressures
    Pre-ride / on the road
    Guideline
  • Lubricate drive chain
    Pre-ride / on the road
    Guideline

    Lube warm, ideally at the end of the riding day so it soaks in overnight. Sooner after rain.

On the road: every 800 km

1 item
  • Check coolant level
    Pre-ride / on the road
    Guideline

On the road: every 1,000 km

1 item
  • Check chain slack and rear wheel alignment
    Pre-ride / on the road
    Guideline

Every 1,600 km or 6 months

1 item
  • Inspect tire tread, sidewalls and date codes
    Wheels and tires
    Guideline

Every 5,000 km or 12 months

10 items
  • Check throttle cable(s) free play and return
    Fuel and air
    Guideline
  • Clean drive chain thoroughly (remove and soak, re-lube)
    Final drive
    Guideline

    Non O-ring chains on old machines: remove, clean, soak in hot chain grease or lube, refit with the master link clip closed end leading.

  • Inspect chain and sprockets for wear (measure stretch)
    Final drive
    Guideline
  • Check steering head bearing adjustment
    Front end
    Guideline
  • Inspect fork seals, stanchions and fork boots
    Front end
    Guideline
  • Check footrests, pegs, rear brake and gear lever pivots
    Rear suspension and frame
    Guideline
  • Grease and check center / side stand and springs
    Rear suspension and frame
    Guideline
  • Check brake pads and discs
    Brakes
    Guideline
  • Check spoke tension and wheel true
    Wheels and tires
    Guideline
  • Check wheel bearings for play
    Wheels and tires
    Guideline

Every 6,500 km or 12 months

1 item
  • Inspect, clean and gap spark plugs
    Engine
    Guideline

Every 8,000 km or 12 months

2 items
  • Change engine oil
    Engine
    Guideline

    Pre-1970 machines: many owners run non-detergent or classic-spec oil with no filter, so short intervals matter. Dry sump: drain the tank and the crankcase/sump, flush the tank and clean the feed and return screens.

  • Replace oil filter
    Engine
    Guideline

Every 9,500 km or 12 months

7 items
  • Inspect coolant hoses and clamps
    Engine
    Guideline
  • Clean / inspect air filter
    Fuel and air
    Guideline

    Mesh or oiled foam: clean and re-oil. Paper: blow out or replace. Some very early machines have no filter at all.

  • Check charging voltage and regulator / cut-out
    Ignition and electrics
    Guideline
  • Check swingarm bushes for play
    Rear suspension and frame
    Guideline
  • Inspect rear shocks for leaks and damping
    Rear suspension and frame
    Guideline
  • Lubricate control cables and lever pivots
    Controls and cables
    Guideline
  • Lubricate speedometer / tachometer cables, check drive
    Controls and cables
    Guideline

    A dry speedo cable whips the needle and eventually kills the instrument.

Every 16,000 km or 2 years

1 item
  • Compression test (or leak-down)
    Engine
    Guideline

Every 19,500 km or 2 years

4 items
  • Replace air filter element
    Fuel and air
    Guideline
  • Synchronize throttle bodies
    Fuel and air
    Guideline
  • Clean and grease rear suspension linkage
    Rear suspension and frame
    Guideline
  • Grease swingarm pivot
    Rear suspension and frame
    Guideline

Every 24,000 km or 3 years

1 item
  • Change fork oil
    Front end
    Guideline

    Some early telescopic forks are grease filled or use very small oil quantities. Check your manual.

Every 24,000 km or 4 years

1 item
  • Check valve clearances (shim adjusted)
    Engine
    Guideline

Every 25,500 km or 4 years

1 item
  • Replace spark plugs
    Engine
    Guideline

Every 29,000 km

1 item
  • Replace chain and sprockets (wear based)
    Final drive
    Guideline

Every 32,000 km or 4 years

2 items
  • Repack / replace steering head bearings
    Front end
    Guideline

    Many old machines use loose balls in cups and cones. Taper roller conversions are common.

  • Repack / replace wheel bearings
    Wheels and tires
    Guideline

    Cup-and-cone and taper roller hubs need periodic repacking and adjustment.

Every 38,500 km or 4 years

1 item
  • Replace fuel filter
    Fuel and air
    Guideline

Every 40,000 km or 6 years

1 item
  • Replace swingarm bushes / bearings
    Rear suspension and frame
    Guideline

Every 48,500 km or 6 years

1 item
  • Rebuild forks: seals, bushes, springs
    Front end
    Guideline

Every 5 h

3 items
  • Coolant (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check every 5 hours; change and/or add if necessary.

  • Rear chain sprocket (check)
    Final drive
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check every 5 hours; replace as required.

  • Brake pads (check)
    Brakes
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check every 5 hours; replace as required.

Every 10 h

11 items
  • Engine oil and filter (replace)
    Engine
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Replace every 10 hours.

  • Exhaust pipe and muffler (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check every 10 hours; replace as required.

  • Rear suspension linkage bushings (lubricate)
    Engine
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Grease every 10 hours.

  • Roller cages and linkage pins of rear suspension (lubricate)
    Engine
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Grease every 10 hours.

  • Air filter (clean and lubricate)
    Fuel and air
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Clean and lubricate after the first 2.5 hours, then every 10 hours.

  • Fuel pipes (check)
    Fuel and air
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check every 10 hours, replace every 40 hours; replace as required.

  • Chain guide / chain guard (check)
    Final drive
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check every 10 hours; replace as required.

  • Secondary drive chain (check and lubricate)
    Final drive
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check and lubricate after the first 2.5 hours, then every 10 hours; replace as required.

  • Rear swingarm bushing (lubricate)
    Rear suspension and frame
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Grease every 10 hours.

  • Swingarm axle roller cages (lubricate)
    Rear suspension and frame
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Grease every 10 hours.

  • Complete throttle control (check and lubricate)
    Controls and cables
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check and lubricate every 10 hours.

Every 20 h

9 items
  • Footpegs, pins, springs (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check every 20 hours; replace as required.

  • Gear shift pedal (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check every 20 hours.

  • Radiators (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check every 20 hours.

  • Radiators to water pump hose (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check every 20 hours.

  • Sprocket bolt tightening (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check after the first 2.5 hours, then every 20 hours.

  • Water hoses and clamps (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check every 20 hours.

  • Rear chain slider (check)
    Final drive
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check every 20 hours; replace as required.

  • Steering head, bottom yoke with stem (lubricate)
    Front end
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Grease every 20 hours.

  • Wheel spoke tension (check)
    Wheels and tires
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check after the first 2.5 hours, then every 20 hours.

Every 30 h

6 items
  • Handlebar mounts and fasteners (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check every 30 hours.

  • Kick start pedal (lubricate)
    Engine
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Grease every 30 hours.

  • Torque of nuts and bolts (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check after the first 2.5 hours, then every 30 hours.

  • Rear frame and engine mounting bolts (check)
    Rear suspension and frame
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check after the first 2.5 hours, then every 30 hours.

  • Front brake disc (check)
    Brakes
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check every 30 hours; replace as required.

  • Rear brake disc (check)
    Brakes
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check every 30 hours; replace as required.

Every 40 h

8 items
  • Front braking system fluid (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check every 40 hours, replace every 80 hours.

  • Rear braking system fluid (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check every 40 hours, replace every 80 hours.

  • Fuel pipes (replace)
    Fuel and air
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Replace every 40 hours.

  • Complete clutch control (overhaul)
    Primary and gearbox
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Overhaul every 40 hours.

  • Chain guide roller, bearings (check)
    Final drive
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check every 40 hours.

  • Sidestand (check)
    Rear suspension and frame
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check every 40 hours.

  • Master cylinder to brake caliper hoses (check)
    Brakes
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check every 40 hours; replace as required.

  • Throttle cables (check and lubricate)
    Controls and cables
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check/lubricate every 40 hours; replace as required.

Every 50 h

12 items
  • Crankcase bearings (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check every 50 hours, replace every 80 hours.

  • Cylinder (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check every 50 hours, replace every 100 hours; replace as required.

  • Oil pump (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check every 50 hours; replace as required.

  • Piston (replace)
    Engine
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Replace every 50 hours.

  • Spark plug (replace)
    Engine
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Replace every 50 hours.

  • Valve springs, rocker arms and plates (check)
    Engine
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check every 50 hours.

  • Valves (check clearance)
    Engine
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check clearance every 50 hours, replace every 100 hours.

  • Clutch hub (check)
    Primary and gearbox
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check every 50 hours; replace as required.

  • Primary drive gear pair (check)
    Primary and gearbox
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check every 50 hours; replace as required.

  • Timing chain / timing chain slider (check)
    Final drive
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check every 50 hours.

  • Timing chain gears (check)
    Final drive
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check every 50 hours.

  • Timing chain tensioner (check)
    Final drive
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check every 50 hours.

Every 60 h

1 item
  • Wheel hub bearings (check)
    Wheels and tires
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Check every 60 hours; replace as required.

Every 80 h

5 items
  • Crankcase bearings (replace)
    Engine
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Replace every 80 hours.

  • Crankshaft (replace)
    Engine
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Replace every 80 hours.

  • Crankshaft oil seals (replace)
    Engine
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Replace every 80 hours.

  • Front braking system fluid (replace)
    Engine
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Replace every 80 hours.

  • Rear braking system fluid (replace)
    Engine
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Replace every 80 hours.

Every 100 h

2 items
  • Cylinder (replace)
    Engine
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Replace every 100 hours.

  • Valves (replace)
    Engine
    Factory

    Factory: Scheduled maintenance chart for TXC - TE 250R / TXC - TE 310R racing motorcycles, full power (Husqvarna TE 250R - 310R / TXC 250R - 310R 2013 USA operation and maintenance book, Appendix A2-A16). Columns: after first 2.5 hours; every 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 hours; replace as required. Legend: S replace, C check, C (•) check clearance, P clean, R overhaul, L grease/lubricate, X replace as required, * change and/or add if necessary. Notes: replace gaskets and seals after each removal; replace screws and bolts if damaged; perform a general inspection after riding on muddy or sandy terrain. Replace every 100 hours.

Every 6 months

1 item
  • Clean battery terminals, check charge and strap
    Ignition and electrics
    Guideline

Every 2 years

5 items
  • Replace coolant
    Engine
    Guideline
  • Inspect wiring, bullet connectors and ground points
    Ignition and electrics
    Guideline
  • Replace hydraulic clutch fluid
    Primary and gearbox
    Guideline
  • Inspect frame, welds and lugs for cracks
    Rear suspension and frame
    Guideline
  • Replace brake fluid
    Brakes
    Guideline

Every 4 years

3 items
  • Replace fuel lines
    Fuel and air
    Guideline

    Old rubber and modern ethanol fuel do not mix well.

  • Inspect brake hoses; replace old rubber
    Brakes
    Guideline
  • Rebuild calipers and master cylinders (seals)
    Brakes
    Guideline

Every 6 years

2 items
  • Replace inner tubes and rim tape with tires
    Wheels and tires
    Guideline
  • Replace tires on age (regardless of tread)
    Wheels and tires
    Guideline

Guideline lines: Intervals here are general guidelines for the machine's era and layout, compiled for this app. They are not factory manual figures. Check your workshop manual, and edit any interval in the bike's Schedule tab.

Keep up with this schedule on your phone

Add the bike in the app and this chart loads itself, ready to log against and edit.

Coming soon to Google Play

Other 2008 Husqvarna models

All 2008 Husqvarna
1985-2013
WR 125
Factory
1986-2010
TE 510
Factory
1987-2013
WR 250
Factory
1991-2010
TE 610
Factory
1997-2013
WRE 125
Factory
1999-2013
CR 125
Guideline
1999-2010
SM 610
Factory
2000-2011
SM 125
Guideline